Miele washer, dryer, dishwasher, oven and coffee system repair
Miele is unusual among appliance makers in how much it builds itself: motors, pumps, control electronics and the stainless honeycomb drum in its washers are produced in-house and tested to the equivalent of twenty years of use. That shows in the W1 washers, T1 heat-pump dryers, G 7000 dishwashers with AutoDos PowerDisk dosing, H 7000 ovens, combi-steam ovens, MasterCool refrigeration and the CM and CVA coffee systems that fill many design-led kitchens in Los Angeles, Orange and Ventura counties.
Independent Miele repair in Los Angeles, Orange and Ventura counties · Diagnostic from $69, applied to the repair · 30–90-day parts & labor warranty

Luxury brand
What we see on Miele service calls
Longevity does not mean nothing wears: washers log F-codes for drain pumps, heaters and door locks, heat-pump dryers lose performance when their fluff filters and condenser fins clog, dishwashers throw F11 or F24 codes, and coffee systems need brew unit and valve service. Pros Fix Appliances reads the fault memory, diagnoses by model and serial, quotes in writing before any work and fits OEM Miele parts.
Diagnose your Miele appliance
Pick the appliance and what it's doing — likely causes, a quick check and the usual price.
- Diagnostic
- From $69$85 refrigeration · applied to the repair
- Same-day
- Call before noonMost LA, OC & Ventura calls seen today
- Warranty
- 30–90 daysparts and labor
Lines we service
- W1 front-load washers (and legacy W3000/W4000 series)
- T1 heat-pump and vented dryers
- G 7000 and G 5000 dishwashers (and legacy G 4000/G 6000)
- H 7000 series ovens and DGC combi-steam ovens
- KM induction and gas cooktops
- MasterCool and K series refrigeration
- CM countertop and CVA built-in coffee systems
Common Miele problems
| Appliance | Symptom | Usual cause |
|---|---|---|
| W1 washer | F11 or water left in the drum after the cycle | The drain pump is blocked by coins, bra wires or lint, or the pump impeller has failed; the filter behind the lower flap needs clearing. |
| W1 washer | F20 or cold washes | The heater element or its NTC temperature sensor has failed, so the control cannot reach the set temperature and raises a heating fault. |
| T1 heat-pump dryer | Clothes still damp after a full cycle | Lint has passed the fluff filters and coated the heat exchanger fins, or the condensate pump and float are stuck; both choke airflow and drainage. |
| G 7000 dishwasher | F11 or F24 on the display | F11 is a drain fault from a blocked pump or non-return valve; F24 indicates the heater relay on the electronics has failed. |
| H 7000 oven | Oven stops heating or shows a fault number | A failed heating element, a cooling fan or temperature sensor fault, or a power module relay; the fault memory names the circuit. |
| CVA built-in coffee system | No coffee dispensed or machine asks to descale repeatedly | Scale in the flow heater and valves from hard water, a worn brew unit seal, or a grinder jammed with oily beans. |
| MasterCool refrigerator | Temperature alarm or ice maker stopped | Evaporator fan or defrost sensor faults, a dirty condenser at the top of the column, or a failed water valve feeding the ice maker. |
Parts
Miele controls its parts tightly, so we order most components through OEM channels against your model and serial number; typical lead time is three to ten business days. The truck carries the items that resolve the majority of first visits: drain pumps for common W1 and G series units, door lock assemblies, heater NTC sensors, dryer filters and descaling supplies.
Finding your model number
Miele data plates list the model and serial. On washers and dryers it is inside the door, on the rim of the porthole; on dishwashers along the top or side edge of the door; on ovens on the frame of the cavity; on refrigeration inside on the side wall. Have it ready when you call and we'll bring the likely parts on the first visit.
Show me where the label is
Show me where the label is
Tell dispatch the model number and the technician brings the likely parts on the first visit. The label is almost always in one of two places.
- Look here first
- Front-loaders: around the door opening
- Then check
- Top-loaders: under the lid, then the left side or the back
- Copy every character, including a suffix after a dash or slash — it can change which part fits. Watch 0 and O, 1 and I, 8 and B.
- A photo of the label is even better: hold a flashlight at an angle so it doesn't glare, and send it when you book.
- No tools needed — open doors, drawers and lids only. Don't pull out a gas range or dryer, and never open a microwave's cabinet.
Typical lifespan
Designed and tested for 20 years of use; 15–20 years is realistic for washers, dryers and dishwashers with regular filter and descaling maintenance. Our rule of thumb for repair versus replacement: if the quote is under half the cost of a comparable new unit and the appliance has life left, repair wins — and the diagnostic fee is applied either way.
Repair or replace your Miele? Run the 50% rule
Repair or replace your Miele? Run the 50% rule
Our rule of thumb: repair when the quote is under half the installed price of a comparable new one and the appliance has life left. Try your numbers.
Repair when the quote is under half the price of a new one and the appliance has life left — typically 10–12 years for a washer.
Rough installed prices and typical lifespans from our technicians' experience, the brand notes on this site and NAHB's study of home-component life expectancy. A written quote and a real price on a new unit beat any estimate — and if a repair isn't worth it, we'll tell you.
Related services
Miele questions
Do you use genuine Miele parts?
Yes. Miele builds most of its own components and the fit and calibration of its pumps, heaters and electronics are specific enough that OEM parts are the only sensible choice. We order them against your model and serial, usually a three-to-ten-day wait, and every replaced part and the labor to fit it carry a 30–90-day warranty depending on the part.
My Miele dryer runs but the clothes stay damp. What is wrong?
On a heat-pump T1 dryer the usual cause is restricted airflow: lint that slipped past the door and plinth filters has coated the heat exchanger, or the condensate pump is stuck and water is backing up. We open the lower section, clean the exchanger fins and drain path, test the pump and sensors and confirm drying times are back to normal.
Are you affiliated with Miele?
No. Pros Fix Appliances is an independent appliance repair company and is not affiliated with or endorsed by Miele. We service Miele laundry, dishwashers, ovens, refrigeration and coffee systems throughout Los Angeles, Orange and Ventura counties, including built-ins in high-rise residences, with a $69 diagnostic for most residential appliances that is applied to the repair if you approve the written quote.
Miele repair near you
From Beverly Hills and Calabasas to Newport Beach, the same technicians and pricing.
- Miele repair in Agoura Hills
- Miele repair in Arcadia
- Miele repair in Bel Air
- Miele repair in Beverly Hills
- Miele repair in Brentwood
- Miele repair in Burbank
- Miele repair in Calabasas
- Miele repair in Century City
- Miele repair in Culver City
- Miele repair in Downtown Los Angeles
- Miele repair in Eagle Rock
- Miele repair in Encino
- Miele repair in Anaheim
- Miele repair in Costa Mesa
- Miele repair in Fullerton
- Miele repair in Huntington Beach
- Miele repair in Irvine
- Miele repair in Laguna Niguel
Miele not working? Call before noon for same-day service.
Tell dispatch the model number and the symptom. We arrive with the likely parts and a written quote before any work.