Short answer: Glendale’s water is hard to very hard: Glendale Water & Power’s 2024 water quality report lists hardness of 143 to 580 ppm by source, about 8 to 34 grains per gallon. In a dishwasher, hard water leaves spots and film and scales heaters, valves and spray arms. Use rinse aid, match the hardness setting, descale regularly and clean the filter.
For Glendale homeowners and renters pulling cloudy glasses out of the dishwasher: how hard the city’s water is, what it does inside a dishwasher, the fixes that work, and when scale has damaged a part.
How hard is Glendale’s water?
Glendale’s water is hard to very hard. Glendale Water & Power (GWP) blends water imported through the Metropolitan Water District (MWD) with local groundwater, and every source in its 2024 report tested above 140 ppm.
GWP’s 2024 water quality report lists hardness in parts per million (ppm) for each source. Dividing by 17.1, as the report’s footnote explains, gives grains per gallon (gpg), the unit most dishwasher manuals use.
| Source (GWP 2024 report) | Hardness, ppm (average) | Grains per gallon |
|---|---|---|
| MWD Weymouth plant (imported) | 241–303 (272) | about 14–18 |
| MWD Jensen plant (imported) | 143–153 (148) | about 8–9 |
| Glendale Water Treatment Plant | 350 | about 20 |
| Glorietta Well 3 (local groundwater) | 440–510 (488) | about 26–30 |
| Glorietta Well 6 (local groundwater) | 470–580 (535) | about 27–34 |
On GWP’s own water hardness scale, 7–10 gpg is hard and anything over 10 gpg is very hard. In 2024, 62.1% of Glendale’s water was bought from MWD and 32.6% came from local groundwater, and GWP notes that hardness varies across the city as the two blend. The hardness of imported water swings from year to year (MWD’s Weymouth supply averaged 102 ppm in GWP’s 2023 report and 272 ppm in 2024), but the local wells stayed above 400 ppm both years. GWP publishes a new report each July. Hard water is safe to drink, GWP says; the trouble starts when it’s heated.
How does hard water damage a dishwasher?
Hard water carries dissolved calcium and magnesium, and a dishwasher heats that water and lets it dry, which turns the minerals back into solid scale. The damage builds a little every cycle.
- Spots and film on dishes. Each drying droplet leaves its minerals behind, most visibly on glasses and dark plates.
- Clogged spray-arm holes. Scale narrows the jets, so one rack comes out dirtier than the other.
- Scaled heating parts. Scale insulates the heating element, or the heater built into the circulation pump on many European-designed machines such as Bosch. Cycles run longer and the part runs hotter until it fails.
- A slow inlet valve. The valve’s small screen and seat scale up, so the dishwasher fills slowly or short.
Hard water film or etching: the vinegar test
Soak a cloudy glass in white vinegar for five minutes. If the glass comes out clear, the cloudiness was mineral film from hard water and the fixes below will work. If it stays cloudy, it’s etching: permanent damage to the glass surface.
GWP itself recommends a mild vinegar solution for fresh mineral deposits on glass and metal. Etching is a different problem, caused mostly by too much detergent in soft or softened water, and no cleaner reverses it. If you have a whole-house softener and your glasses are etching, cut the detergent dose.
How do you stop hard water spots in a dishwasher?
Five habits stop most hard water spots and scale in a dishwasher: rinse aid, the right hardness setting, salt if the machine takes it, regular descaling and a clean filter.
- Keep the rinse aid dispenser full. Rinse aid makes the final rinse sheet off instead of beading, so fewer droplets dry into spots; turn the dispenser up one setting if spots persist. It helps drying too, as our guide to a dishwasher not drying dishes explains.
- Set the water-hardness setting. GWP notes that many dishwashers have one, usually in grains per gallon. With Glendale sources at about 8 to 34 gpg, start at your manual’s setting for very hard water, or the softened level if you have a whole-house softener.
- Fill the salt reservoir if there is one. Some European-designed dishwashers, Miele among them, have a built-in softener that recharges with coarse dishwasher salt through a screw cap in the tub floor beside the filter. Use dishwasher salt only, never table salt or detergent, and fill it just before a cycle so spilled brine rinses away. No cap means no softener.
- Descale every one to two months. Run an empty hot cycle with a citric-acid dishwasher cleaner or your manufacturer’s descaler, following the label. Glendale water rebuilds scale quickly, so don’t wait for white crust on the spray arms.
- Clean the filter and spray arms monthly. Most current dishwashers have a twist-out filter in the tub floor; clear scaled spray-arm holes with a toothpick. Fisher & Paykel drawers use a filter plate instead, covered in our guide to a Fisher & Paykel DishDrawer not draining.
When has hard water scale damaged a part?
Hard water scale has damaged a part when the symptoms survive a descale: dishes come out cold and wet, cycles run far longer than they used to, the dishwasher fills slowly, or it hums without the sound of spraying water.
| Symptom after descaling | Likely part | Typical LA price |
|---|---|---|
| Cold, wet dishes; long cycles; heating error code | Heating element | $220–$380 |
| Same symptoms on a machine with the heater in the pump | Circulation pump with heater | $280–$520 |
| Slow fill, low water, fill error code | Water inlet valve | $170–$300 |
| Hum with no spray; poor washing on both racks | Wash pump or circulation motor | $280–$520 |
| Water left in the bottom after the filter is clean | Drain pump | $190–$330 |
Prices are parts and labor across LA County and Orange County and vary by brand and model. The $69 dishwasher diagnostic includes a written quote and is applied to the repair. Then use the 50% rule: repair when the quote is under half the price of a comparable new dishwasher and the machine has life left, roughly 10–12 years for a mainstream model.
When to call a technician
Call a technician when water reaches the floor, the dishwasher trips a breaker or smells hot, or a descale hasn’t brought back heat, fill or spray. Switch the dishwasher off at its breaker before looking under the kick plate, and close the hot-water valve under the sink if it’s leaking.
Pros Fix Appliances is based in Glendale (see our Glendale appliance repair page) and repairs dishwashers across Los Angeles County and Orange County. Call before noon and we can usually come the same day; later calls are typically seen the next business day, with the same fees everywhere and no travel charge. Call (866) 696-7767 or book online, or read more about our dishwasher repair service.
Frequently asked questions
Is Glendale tap water hard?
Yes. Glendale Water & Power’s 2024 water quality report lists hardness from 143 to 580 ppm depending on the source, roughly 8 to 34 grains per gallon. GWP calls anything over 10 grains per gallon very hard, and hardness varies across the city as imported water blends with groundwater.
What hardness setting should I use on my dishwasher in Glendale?
Start with your manual’s setting for very hard water, since Glendale’s sources ran about 8 to 34 grains per gallon in GWP’s 2024 report. With a whole-house water softener, use the softened level instead; too much detergent in soft water can etch glass.
Do I need dishwasher salt?
Only if your dishwasher has a built-in water softener, marked by a screw cap in the tub floor next to the filter; many Miele dishwashers have one. Without a salt reservoir, salt does nothing, so rely on rinse aid, the hardness setting and regular descaling.
