White plates and a glass jar standing in a dishwasher rack, seen from above

Fisher & Paykel DishDrawer Not Draining? Filter, Hose and Pump Checks

Short answer: A Fisher & Paykel DishDrawer not draining usually has a blocked drain filter or filter plate, a kinked or sagging drain hose, or a clogged disposal or sink drain downstream. Clean the filters and check the hose first. If water still sits above the filter plate, the drain pump needs a technician, typically $190–$330 in Los Angeles after a $69 diagnostic.

This guide is for Fisher & Paykel DishDrawer owners who open a drawer to dirty water in the bottom. The checks below follow Fisher & Paykel’s own user and installation guides, in the order we work through them, with what the fault codes mean and what repairs cost across Los Angeles County and Orange County.

How much water is normal in a DishDrawer?

A little water under the drain filter is normal in a Fisher & Paykel DishDrawer; the user guide says it needs no action. Water standing above the filter plate after a cycle is not.

The filter plate is the flat metal plate covering the bottom of the drawer, and the drain filter is the small removable filter that sits flush in it. Lift the drain filter out and you’ll usually see some water in the sump below it; that’s by design. A drawer that finishes a cycle with water over the plate has a drain problem.

Why is my Fisher & Paykel DishDrawer not draining?

A Fisher & Paykel DishDrawer that won’t drain is usually blocked rather than broken. These are the causes in the order we check them:

Cause Signs Fix Typical LA price
Blocked drain filter or filter plate Food on the plate; dirty dishes; water above the plate Clean both (steps below) Free
Kinked, sagging or misrouted drain hose Started after the drawer was pulled out or the cabinet was worked on Straighten the hose and restore the high loop Free, or covered by the $69 diagnostic
Blocked disposal, air gap or sink drain The sink drains slowly too, or the disposal was just jammed or replaced Clear the disposal and air gap; remove a new disposal’s knockout plug Free (a house-drain clog is a plumber’s job)
Jammed or failed drain pump Water stays after the filters and hose are clear Clear debris from the pump or replace it $190–$330
Motor or control fault Continuous beeping and a fault code Note the code; technician diagnosis Wash motor $280–$520; control board $260–$560

How do you clean a Fisher & Paykel DishDrawer filter?

Fisher & Paykel recommends cleaning the DishDrawer drain filter whenever you see food particles, and the spray arm about once a month. The job takes about five minutes.

  1. Turn the DishDrawer off at the power supply or unplug it.
  2. Lift the access panel on the base rack if your model has one, then lift out the drain filter. Some water may spill; that’s normal.
  3. Empty the drain filter and rinse it under running water.
  4. To remove the filter plate, turn the outer of the two rings in its center counterclockwise about 1/8 turn and lift the plate out. Mind the sharp outer edge.
  5. Wash the plate in hot soapy water, rinse it, and lift out the spray arm to shake out any debris.
  6. Refit the spray arm and plate, and seat the drain filter flush with the plate; Fisher & Paykel says the drawer must run with all three in place. Restore power and run a rinse cycle.

In hard-water areas such as Glendale, white scale builds on the plate and spray arm too; our guide to hard water and dishwashers covers descaling.

Could the drain hose or the sink drain be the problem?

The drain hose or the sink drain is the next suspect. Fisher & Paykel’s installation guide lists kinked drain hoses, a blocked waste connection and a high loop that isn’t installed properly as the causes of water left above the filter plate after the rinse.

  • The high loop and kinks. The drain hose should rise to a loop at least 6 inches (150 mm) above the drain hose joiner, with any extra hose kept on the DishDrawer side of the loop. A sagging hose holds water, and one pinched behind the cabinet stops the drain.
  • The disposal. A jammed or full garbage disposal blocks the drain. Run it with cold water first; if it hums instead, follow our reset for a humming garbage disposal. On a new disposal, the knockout plug in its dishwasher inlet has to come out.
  • The air gap. If there’s a small cap beside the faucet (Fisher & Paykel calls it an air break), pull the cover and clear any debris.
  • One drawer or both? Both drawers of a double DishDrawer drain to the same household drain. Water in both points downstream to the shared hose, disposal or sink drain; water in one points to that drawer’s filter, hose or pump.

If the kitchen sink drains slowly too, the clog is in the house drain, which is a plumber’s job rather than a DishDrawer repair.

What do Fisher & Paykel DishDrawer fault codes mean?

A Fisher & Paykel DishDrawer signals a fault with a continuous beep about once a second and a code on the display. Codes vary by generation, so treat this table, taken from Fisher & Paykel’s user guide for its DD60 models, as a guide and check the fault code page in your own model’s guide.

Code Meaning (DD60 user guide) What to do
F1 Flood switch activated Turn off the water supply to the DishDrawer and call for service
F2 Motor problem Call for service
F3 Temperature sensor failed Check the incoming water is below 65°C (149°F); a tempering valve may be needed
F4 Faulty temperature sensor or element Call for service
F5, F6, F7 Lid fault Switch the power off and back on; the fault may reset
F9 Electronics malfunction Call for service

Fisher & Paykel’s reset routine: press a button to stop the beeping, turn the DishDrawer off, wait a few seconds and turn it back on. If the code is gone, carry on. If it returns, write it down, switch the drawer off at the power supply and call; the code tells the technician which part to bring. User guides for each model are on Fisher & Paykel’s US support site.

When to call a technician

Call a technician when the filters are clean and the hose and drain are clear but water still sits above the filter plate, or right away for F1, a leak or a burning smell. With water on the floor, turn off the DishDrawer’s water supply and switch it off at the power supply, as Fisher & Paykel advises.

We’re an independent repair company, not a Fisher & Paykel authorized service center, so a DishDrawer still under Fisher & Paykel’s warranty should go to Fisher & Paykel first. Out of warranty, Pros Fix Appliances repairs DishDrawers across Los Angeles County and Orange County; call before noon and we can usually come the same day, otherwise typically the next business day. The $69 diagnostic includes a written quote and is applied to the repair, with no travel charge in either county. Repair when the quote is under half the price of a comparable new unit and the DishDrawer has life left (roughly 10–12 years for a mainstream dishwasher).

Call (866) 696-7767 or book online, or read more about our dishwasher repair service. For a standard door-style dishwasher, see our guide to a dishwasher not draining.

Frequently asked questions

What does F1 mean on a Fisher & Paykel DishDrawer?

In Fisher & Paykel’s DD60 user guide, F1 means the flood switch has been activated: water has reached a place it shouldn’t. Turn off the water supply to the DishDrawer and call for service. Codes vary by generation, so confirm F1 in your own model’s user guide.

Why does only one drawer of my DishDrawer hold water?

Both drawers share the household drain, so water in only one drawer points to that drawer: its drain filter, filter plate, drain hose or drain pump. Clean that drawer’s filters first. Water in both drawers points downstream, to the shared hose, a garbage disposal or the sink drain.

How much does it cost to fix a DishDrawer that won’t drain in Los Angeles?

Often nothing, because clean filters and a straightened hose fix many drain problems. If a part has failed, Pros Fix Appliances charges a $69 diagnostic that’s applied to the repair; a drain pump typically runs $190–$330 and a wash motor $280–$520, parts and labor, in LA County and Orange County.

About the author — Emanuel “Manny” Misayeledis is the owner and lead technician of Pros Fix Appliances in Glendale (California BHGS registration A49955). He and his team repair residential and built-in appliances across Los Angeles County and Orange County. Last updated: November 3, 2026.

Scroll to Top