Short answer: A garbage disposal humming but not working is usually jammed: a pit, bone or bottle cap has locked the spinning plate. Cut the power, turn the plate from below with a 1/4-inch hex key, press the red reset button and test with cold water. If it still hums, the motor is failing; replacement runs $320–$560 installed in Los Angeles.
For anyone whose disposal hums instead of grinding: the five-step reset that clears most jams, what not to do, how to tell a jam from a dead motor, and what a replacement costs across Los Angeles, Orange and Ventura counties.
Why is my garbage disposal humming but not working?
A humming garbage disposal is getting power, but its motor can't turn. Usually something is wedged in the grinding chamber; less often, the motor itself is failing.
A spinning plate at the bottom of the chamber (the turntable, or flywheel) flings food against a fixed grinding ring. A fruit pit, bone, bottle cap or shard of glass can wedge between the two and lock the plate. The stalled motor hums and heats up until a built-in overload protector cuts it off, so a hum followed by silence usually means the overload has tripped.
| Cause | What you notice | Fix | Typical LA price |
|---|---|---|---|
| Jammed object | Hum; the plate turns with a hex key | The 5-step reset below | Free, or covered by the $69 diagnostic |
| Overload tripped | Hum, then silence; red button sticks out | Let it cool, press reset | Free |
| Seized motor bearing | Hex key won't turn | Replace the disposal | $320–$560 installed |
| Failed motor | Plate turns freely but it still only hums | Replace the disposal | $320–$560; $480–$780 for 1 HP quiet |
How do you reset a humming garbage disposal in 5 steps?
A 1/4-inch hex key, also called an Allen wrench, clears most garbage disposal jams in about two minutes. InSinkErator ships a crank-shaped wrench for this with every disposal and lays out the same routine on its jammed-disposal support page.
- Cut the power. Turn the wall switch off, then unplug the disposal under the sink or switch off its breaker.
- Look, don't reach. Find the object with a flashlight and lift it out with tongs or pliers. Never use your hand.
- Turn the plate from below. Put the key in the hex socket dead center on the bottom of the unit and work it back and forth until it turns full circles freely both ways. Firm pressure is fine; InSinkErator's wrench is designed to bend before the disposal breaks. No socket? Some builder-grade units are freed from above with a wooden spoon handle, power still off.
- Press the red reset button. It's on the bottom, facing the floor, and sticks out about 1/4 inch (5 mm) when tripped. If it won't stay in, wait 10 minutes for the motor to cool.
- Test with cold water. Restore power, run a moderate stream of cold water, then switch the disposal on. If it jams again, repeat steps 1 to 3.
Afterward, keep bottle caps, twist ties and utensils out of the sink, run cold water while grinding and never pour grease down the drain.
What not to do with a jammed disposal
Three habits turn a jammed disposal from a free fix into an injury or a dead motor:
- Reaching in. Keep your hand out of the chamber even with the power off; use tongs or pliers.
- Chemical drain cleaner. It can't dissolve a pit or a bottle cap, and it leaves caustic liquid where you're about to work. InSinkErator advises keeping harsh cleaning products out of disposals.
- Repeated restarts. A stalled motor overheats; every try trips the overload again and wears the motor.
What if the garbage disposal still hums after a reset?
A garbage disposal that still hums after the reset has a second problem, and the hex key tells you which:
- Key turns freely, still hums: the motor or its start circuit has failed, and the disposal needs replacing.
- Key won't turn with firm pressure: a hidden object or a seized bearing, which can happen after months without use. Stop forcing it.
- Reset button trips again within seconds: a failing motor.
- No sound at all: not a jam. As InSinkErator suggests, check the reset button and the breaker, then plug a lamp into the outlet and flip the switch to see whether the outlet gets power.
- Water dripping from the bottom: an internal seal has failed. See our guide to a garbage disposal leaking from the bottom.
Should you repair or replace a humming garbage disposal?
Clear a jam; replace a garbage disposal whose motor or internal seal has failed. We replace household disposals rather than rebuild them, so on this appliance replacement usually is the repair. Typical prices across LA, Orange and Ventura counties, parts and labor included:
- Jam clearing and reset: covered by the $69 diagnostic
- Flange or connection reseal: $140–$220
- Replacement installed, 1/2–3/4 HP: $320–$560
- Replacement installed, 1 HP quiet series: $480–$780
Check the warranty before paying for a new unit. InSinkErator lists in-home limited warranties from 1–3 years on its Standard Series up to 8–10 years on its Quiet Series, and your model's term is in its manual.
When to call a technician
Call a technician if the hex key won't turn, the reset keeps tripping, the breaker trips, you smell burning or water reaches the outlet under the sink. Leave the disposal unplugged until it's checked.
Pros Fix Appliances clears jams and replaces disposals across Los Angeles, Orange and Ventura counties. Call before noon and we can usually come the same day; later calls are typically seen the next business day. The $69 diagnostic covers clearing a jam and is applied to a replacement if you need one, with no travel charge in either county. Call (866) 696-7767 or book online.
A jammed disposal can also back up a dishwasher that drains through it. If yours still holds water once the disposal runs, see our guide to a dishwasher that won't drain or our dishwasher repair page.
Frequently asked questions
What size hex key fits a garbage disposal?
A 1/4-inch hex key, also called an Allen wrench, fits the socket in the center of the bottom of most InSinkErator disposals. InSinkErator includes a crank-shaped wrench with each unit, and any standard 1/4-inch Allen wrench works if that one is lost.
Where is the reset button on a garbage disposal?
On the bottom of the unit, under the sink, facing the floor: a small red square. When the overload protector trips, it sticks out about a quarter inch. Press it gently; if it won't stay in, let the motor cool for 10 minutes and try again.
Is it safe to keep running a disposal that hums?
No. A humming disposal is a stalled motor: it draws power but can't turn, so it overheats until the overload protector trips, and each restart wears it further. Cut the power and free the jam with a hex key before trying again.
How much does it cost to replace a garbage disposal in Los Angeles?
Pros Fix Appliances installs 1/2–3/4 HP replacement disposals for $320–$560 and 1 HP quiet-series units for $480–$780, parts and labor, across LA, Orange and Ventura counties. Clearing a jam is covered by the $69 diagnostic, which is applied to a replacement if one is needed.
What's your garbage disposal doing?
Still not working? Call before noon and we can usually be there today.
- Diagnostic
- $69applied to the repair
- Same-day
- Call before noonMost LA, OC & Ventura calls seen today
- Warranty
- 30–90 daysparts and labor



