Short answer: An electric stove burner not working is usually a burned-out element, a scorched receptacle (the coil’s socket) or a failed infinite switch behind the knob. On a coil stove, swap the dead element with a working one of the same size: if the problem moves, replace the element. Elements and switches typically cost $150–$290 to replace in Los Angeles.
For anyone with one burner that won’t heat on an electric coil or smooth glass-top stove, from the basic ranges in many LA rentals to a new kitchen. Here’s the 10-minute swap test, how to read a burned socket, why newer coils don’t glow as red, and what each repair costs.
How does an electric stove burner work?
A coil burner is a heating element that plugs into a receptacle, a two-slot socket under the cooktop. The knob is an infinite switch: it doesn’t dim the burner but switches full power on and off in cycles, longer on HI and shorter on LOW. Glass-top stoves use the same switches or a touch-control board, with a radiant element under the glass and a limiter, a heat-sensing safety switch that cycles the element to protect the glass. The whole stove runs on 240 volts.
Why doesn’t a newer electric burner glow as red?
A newer electric burner glows less because coil elements on ranges and cooktops made since June 2018 limit their own temperature. Whirlpool’s coil element help page says the change follows updated UL standards and applies to all brands and replacement coils: the outer coil may not glow as strongly, and the inner coil cycles on and off. Glass tops cycle too; Whirlpool says a radiant element’s limiter can switch it off and on even on HI. A burner that heats a pan but blinks or glows less isn’t broken. A burner that never gets hot is.
Why is my electric stove burner not working?
An electric stove burner usually stops working because of the coil, its socket or its switch. In the order we find them, starting with the free fix:
1. The coil isn’t seated
Whirlpool notes the coil has to be inserted properly to work. Tell: the coil sits crooked or wobbles, or it works only when you press it down.
2. The element has burned out
Tell: a blister, split or bubble on the coil, or it stays cold in every position during the swap test.
3. The receptacle is burned
A loose connection heats up and scorches the socket. Tell: dark, melted or pitted plastic and terminals, or a coil that works only when wiggled. Replace the receptacle and element together: a scorched socket damages a new element’s terminals, and a pitted element damages a new socket.
4. The infinite switch has failed
Tell: a good coil stays cold in that position, or the burner works only on HI. A burner stuck on full heat is also the switch; see electric burner stuck on high.
5. A wire has burned off
Heat at a scorched receptacle or switch can burn through a wire. Tell: scorch marks under the cooktop or behind the knob.
6. Half the power is missing
If several burners and the oven quit at once while the clock still works, check the range’s double breaker before any part; a half-tripped breaker or a loose supply connection does exactly that.
7. On a glass top: the element or limiter
A radiant zone that never glows or heats, even on HI after a few minutes, usually has a burned-out element or a failed limiter. On a dual or triple zone, a dark outer ring with a working center points to that ring or its switch. If a zone quits mid-cook, Whirlpool’s smoothtop troubleshooting says to remove the pan, let the cooktop cool for 30 minutes and try again.
How do you test a coil burner yourself?
The swap test takes about 10 minutes and tells you whether the coil or the stove is at fault.
- Turn every knob off and let the coils cool completely.
- Switch off the range’s double breaker before you reach under a coil.
- Remove the dead coil. Lift its outer edge about an inch and pull it straight out of the receptacle without twisting.
- Inspect the socket. Dark, melted or pitted terminals mean the receptacle needs replacing. Stop there and don’t plug a good coil into it.
- Swap. Plug a working coil of the same size into the dead position, seat it flat, restore power and set it to HI.
- Read the result. If the working coil heats, the original coil is bad. If it stays cold, the receptacle, wiring or switch is at fault. Plugging the suspect coil into a good position confirms it.
- Put everything back with the knobs off and the coils cool.
Stop if you see sparks, smell burning plastic, find scorched wiring or the breaker trips. Don’t probe a receptacle or switch with the power on: the stove runs on 240 volts, and parts of the circuit can stay live with the knob off. Never cook on a cracked glass top; Viking’s electric range manual warns that spills can get through a broken surface and cause a shock, so switch it off at the breaker.
How much does electric burner repair cost in Los Angeles?
Most electric burner repairs cost $150–$290 in Los Angeles and Orange County, parts and labor; glass tops and touch controls cost more.
| Problem | Tell | Fix | Typical LA price |
|---|---|---|---|
| Coil not seated | Wobbles; works when pressed | Reseat it | No part needed |
| Burned-out coil element | Blister or split; cold in every position | New element | $150–$290 |
| Burned receptacle | Dark, melted or pitted socket | New receptacle, usually with a new element | Quoted in writing after testing |
| Failed infinite switch | A good coil stays cold in that spot | New switch | $150–$290 |
| Radiant element (glass top) | Zone never glows on HI | New radiant element | $220–$400 |
| Relay or control board (touch-control range) | Zone dead or erratic, often with an error code | New board | $280–$650 |
| Half-tripped breaker | Several burners and the oven dead, clock on | Reset; call an electrician if it recurs | Not a range part |
The range diagnostic is $69 and is applied to the repair you approve. Fees are the same across LA County and Orange County with no travel charge, and the exact price is in writing before work starts. Most burner repairs pass the 50% rule: repair when the quote is under half the price of a comparable new range and the range has life left (ranges last roughly 15 years). A cracked glass top on an aging range is the repair most likely to fail it, and on some older models the glass is no longer made.
When to call a technician
Call a technician when the swap test points to the receptacle, switch or wiring; when you find scorching or melted plastic; when a glass-top zone won’t heat after a cool-down; and right away if the glass is cracked or a burner won’t turn off.
Pros Fix Appliances repairs electric coil, glass-top and induction ranges and cooktops across Los Angeles County and Orange County. Calls placed before noon are usually seen the same day; later calls are typically seen the next business day. Renters: check with your landlord or property manager before paying for a repair. Call (866) 696-7767 or book online, or see stove and cooktop repair and oven and range repair. Weighing a switch to gas? Read gas vs electric range repair costs.
Frequently asked questions
Why is only one burner on my electric stove not working?
One dead burner points to that burner’s element, receptacle or infinite switch, because the other burners share the same power supply. Swap the coil with a same-size working one: if the problem follows the coil, replace the coil; if it stays put, the receptacle or switch has failed.
Why does my electric burner only work on high?
Usually a worn infinite switch. Its cycling contacts no longer deliver power on the lower settings, and only the HI position, which holds the circuit closed, still works. Swap-test the element first; if a good element behaves the same way in that position, replace the switch, typically $150–$290 in Los Angeles.
Can I replace an electric stove burner myself?
A plug-in coil element is designed to lift out, and swapping in the correct replacement for your model is a reasonable owner job with the breaker off and the coils cool. Receptacles, switches, wiring and glass-top elements mean working on 240-volt connections, so leave those to a technician.
