Clear ice cubes of mixed sizes, including small chips, on a dark blue surface

Ice Maker Making Small or Hollow Cubes? Low Water Flow Causes

Short answer: An ice maker making small or hollow cubes is getting too little water. Because most ice makers fill for a set time, a clogged filter, low water pressure, a kinked line or saddle valve, a partly frozen fill tube or a scaled inlet valve shrinks every cube. Replace the filter first; a new inlet valve typically costs $170–$300 in LA.

This guide is for homeowners and renters whose refrigerator ice maker still works but turns out small, thin or hollow cubes. It explains why low water flow is almost always behind it, the free checks to run in order, and what the repair costs when a part has failed.

Why does an ice maker make small or hollow cubes?

Because the tray isn’t getting enough water. Most refrigerator ice makers open the water inlet valve for a set time rather than measuring the water, so anything that slows the flow puts less water in every cube. GE warns that pressure below 40 psi can cause hollow cubes or slow ice, and Whirlpool says low pressure causes small or hollow cubes.

One quick exception: if only the cubes at the bottom of the bin are small, they’re probably old. Ice slowly shrinks as it sits in a frost-free freezer. Dump the bin and judge the next fresh batch.

What causes small ice cubes, in order?

These are the causes in the order we check them, from cheapest to most involved.

Cause Tell Fix Typical LA price
Clogged or overdue water filter Dispenser slow too; filter over 6 months old Replace the filter Cost of the filter
New filter not seated, or air in it Started right after a filter change; dispenser sputters Reseat and flush Free
Low house pressure or a reverse osmosis (RO) system Weak flow at the sink too, or RO tank drawn down Plumber or RO service; bypass the fridge filter on RO Not an appliance repair
Kinked line, half-open shutoff or piercing saddle valve Began after the fridge was moved; weak flow even without the filter Straighten, open fully, replace the saddle valve Quoted on site
Partly frozen fill tube Cubes shrink, then stop; ice at the fill opening Thaw and fix the cause (air leak or dripping valve) $240–$480 (Samsung, LG)
Scaled or weak water inlet valve Filter and pressure fine, flow still weak Replace the inlet valve $170–$300
Scale on a built-in ice machine Thin or partial cubes from an under-counter unit Descale and service $220–$360

A saddle valve is a clamp-on valve that taps a household pipe. Whirlpool tells installers not to use the piercing type or 3/16-inch versions because they reduce flow and clog more easily. The water inlet valve is the electric valve at the back of the refrigerator that opens to fill the ice maker and the dispenser.

What can you check yourself?

These four free checks cover the common low-flow causes. Unplug the refrigerator before reaching behind it or into the ice maker; the inlet valve runs on 120 volts and sits next to the water connections.

  1. Check the filter date. Whirlpool and Samsung both say to replace it about every 6 months. After a change, confirm the filter is locked in and run water for a couple of minutes to purge air.
  2. Run a flow test.GE’s dispenser test: dispense into a measuring cup for 20 seconds. Less than 8 ounces means low flow. Repeat with the filter removed (some models need a bypass plug in its place); if flow recovers, the filter was the problem.
  3. Check the supply line. Unplug the refrigerator, pull it out gently and look for kinks, a shutoff valve that isn’t fully open, or a piercing saddle valve.
  4. Check the house water. If the kitchen tap is weak too, the problem is household pressure, a job for a plumber. With RO, follow Whirlpool’s water pressure guidance: 40–60 psi at the refrigerator, a full tank, and the fridge filter removed or bypassed.

Stop there if you see water near the valve’s wiring, a cracked fitting or a leak at the back. Shut the water off at the valve and call.

Does hard water in Los Angeles cause small cubes?

Hard water doesn’t shrink cubes directly, but the minerals it carries clog filters faster and build scale on the inlet valve’s screen, which slows the flow. LADWP’s 2026 water quality report (2025 results) shows average hardness of about 103 mg/L for water from the Los Angeles Aqueduct Filtration Plant and about 234–236 mg/L for water from the Metropolitan Water District’s Weymouth and Diemer plants. On the U.S. Geological Survey scale that is moderately hard to very hard.

In practice, that means changing filters on schedule (sooner if your ice looks cloudy or your dispenser slows) and descaling built-in ice machines, where scale on the freezing plate produces thin, partial cubes.

When should you call, and what does the repair cost?

Call when the cubes stay small after a new filter and the flow test still fails, when ice builds up at the fill tube, or when water leaks at the back. Typical prices in Los Angeles County and Orange County, parts and labor:

  • Water inlet valve: $170–$300
  • Fill tube or ice-room repair (Samsung, LG): $240–$480
  • Ice-maker assembly: $220–$420
  • Built-in ice machine descale and service: $220–$360

These usually come in under half the price of a comparable new refrigerator, so on a unit with life left, repair almost always wins. The $85 ice maker diagnostic is applied to the repair, the exact price is written before work starts, and fees are the same across both counties with no travel charge. Calls placed before noon are usually seen the same day. Call (866) 696-7767 or book online; see our refrigerator repair service for what else we check on the visit.

If the ice maker has stopped completely, start with why an ice maker stops making ice; if the dispenser is slow or dry, see refrigerator water dispenser not working.

Frequently asked questions

What water pressure does a refrigerator ice maker need?

It depends on the brand. GE asks for 40–120 psi and warns that pressure under 40 psi can cause hollow cubes or slow ice. Whirlpool lists 30–120 psi and says its refrigerators work best at 40–80 psi. Your owner’s manual gives the figure for your model.

Can a new water filter cause small ice cubes?

For a short while, yes. A filter that isn’t fully locked in restricts flow, and air trapped in a new cartridge makes the first fills short. Check that it’s seated, run water through the dispenser for a couple of minutes, and give the ice maker up to a day to settle.

Does reverse osmosis cause small ice cubes?

It can. Reverse osmosis systems lower water pressure, especially when the storage tank has been drawn down. Whirlpool recommends 40–60 psi at the refrigerator’s inlet with an RO system, letting the tank refill, and removing or bypassing the refrigerator’s own filter so the water isn’t filtered twice.

Is it worth replacing the water inlet valve?

Almost always. A new inlet valve is typically $170–$300 in Los Angeles, parts and labor, a small fraction of a new refrigerator. If the dispenser is slow too, the same valve is often the reason. The $85 diagnostic confirms the valve is at fault and is applied to the repair.

About the author — Emanuel “Manny” Misayeledis is the owner and lead technician of Pros Fix Appliances in Glendale (California BHGS registration A49955). He and his team repair residential and built-in appliances across Los Angeles County and Orange County. Last updated: November 3, 2026.

Scroll to Top