Short answer: An ice maker that won’t stop making ice isn’t getting the ‘bin full’ signal. Usually the bin isn’t seated or sits on the wrong shelf, the shutoff arm is stuck or detached, or an optical sensor or switch has failed. Turn it off, reseat the bin and check the arm; a new ice maker typically costs $220–$420 in LA.
This guide is for anyone whose refrigerator ice maker keeps going until cubes spill out of the bin, jam the freezer drawer or land on the floor. It covers how to stop it right now, why the ice maker isn’t shutting itself off, the free checks, and what a repair costs when a part has failed.
Why won’t my ice maker stop making ice?
An ice maker stops only when something tells it the bin is full, and that signal isn’t getting through. Most refrigerator ice makers use one of two designs. A wire shutoff arm (also called a bail arm) rests on the ice; as the pile rises it lifts the arm, and the ice maker stops when the arm reaches the up position. An optical sensor shines a beam across the bin and stops production when ice blocks it.
Either way, the bin has to sit exactly where the arm or beam expects it. Whirlpool says that if the bin isn’t directly below the ice maker, the shutoff arm won’t work correctly and the ice maker keeps producing. Samsung’s support page gives the same reason first: a bucket or shelf out of position, so ice never piles high enough to reach the sensor or arm.
How do you stop the ice maker right now?
- Turn it off. Lift the wire arm to the up position until it clicks, flip the on/off switch under the ice maker (on some Whirlpool models, “o” is off), or turn the ice maker off in the display settings.
- Don’t rely on pulling the bin. On many models that won’t stop production, and ice then drops loose into the freezer.
- Clear the overflow. Empty the extra ice, pick up anything on the floor so no one slips, and make sure the freezer door or drawer closes fully. A door held open by ice lets in warm air and builds frost.
- Watch for water. If water keeps dripping with the ice maker off, close the refrigerator’s supply valve; the inlet valve may be leaking through.
What causes it, and what does each fix cost?
| Cause | Tell | Fix | Typical LA price |
|---|---|---|---|
| Bin not seated, backwards or on the wrong shelf | Started after cleaning or rearranging the freezer | Reseat the bin, move the shelf to the right rail | Free |
| Max Ice or Fast Ice mode on | Fast production for a day, but it still stops at a full bin | Nothing needed, or turn the mode off | Free |
| Shutoff arm stuck, bent or detached | Arm hangs low on top of a full bin, or is missing | Free it, reattach it or replace it | Free to quoted after testing |
| Optical sensor blocked or failed | In-door or electronic ice maker; bin full, still dropping ice | Clear the sensor path, or replace the sensor | Quoted after testing |
| Ice maker’s internal shutoff switch failed | Arm moves freely to up, ice maker keeps cycling | Replace the ice-maker assembly | $220–$420 |
| Water inlet valve leaking through | Water drips or the tray refills with the ice maker off | Replace the inlet valve | $170–$300 |
| Control board not reading the sensor | Sensor and ice maker test good | Replace the board | $280–$620 |
Prices are for Los Angeles County and Orange County, parts and labor; built-in units such as Sub-Zero run higher, with built-in ice maker or valve jobs typically $320–$620. The exact price is written before work starts.
What can you check yourself?
Turn the ice maker off before reaching in; its mechanism can move without warning. Then:
- Reseat the bin. Push it all the way in, the right way around. On Samsung’s Bespoke 4-Door Flex, the ice shelf belongs on the highest rail.
- Check the arm. It should swing up and down freely, stay attached at both ends and not be held down by a clump of ice. On Sub-Zero units, Sub-Zero’s guide says to confirm both the shut-off arm and the rudder arm are attached.
- Look for an ice mode. Turn off Max Ice, Fast Ice or a similar setting; Sub-Zero’s Max Ice raises production for 24 hours.
- Test the shutoff (arm-style ice makers). Lift the arm to the up position and leave it there. The ice maker may finish a cycle already under way, but it shouldn’t start another. If it keeps cycling with the arm up, its shutoff switch has failed.
Stop and call if water leaks from the freezer or behind the refrigerator, if the ice maker is cracked, or if the freezer has started to frost up because the door couldn’t close.
Is it making too much ice, or is the bin just filling?
A working ice maker produces steadily until the bin is full, which can look like “too much” after you’ve emptied it. Sub-Zero says its ice maker makes about eight cubes every 2–3 hours on average and the bin can take 1–2 days to fill. If the ice stops when the pile reaches the arm or sensor, the ice maker is working as designed.
When should you call, and is it worth repairing?
Call when the bin, arm and modes check out but ice keeps coming, or right away if water is leaking. Repair is almost always worth it: an ice-maker assembly at $220–$420 or an inlet valve at $170–$300 is a small fraction of a new refrigerator. The ice maker diagnostic is $85 and is applied to the repair, with the same fees across Los Angeles County and Orange County and no travel charge.
Calls placed before noon are usually seen the same day; later calls typically the next business day. Call (866) 696-7767 or book online, and see our refrigerator repair service for the rest of what we check.
If your ice maker has the opposite problem, see why an ice maker stops making ice; if overflowing ice has held the door open, see frost build-up in the freezer.
Frequently asked questions
How does an ice maker know when the bin is full?
It uses either a wire shutoff arm or an optical sensor. The arm rests on the ice, and the rising pile lifts it to the off position. An optical sensor shines a beam across the bin and stops production when ice blocks it. Samsung, for one, uses both designs depending on the model.
Will removing the ice bin stop the ice maker?
Not on most models. Sub-Zero says removing the bin alone won’t stop production; you have to raise the ice level arm. On models with a switch or an on/off setting in the display, turn it off there. Don’t run a freezer ice maker without its bin, or ice drops straight into the freezer.
Why is my ice maker overflowing onto the floor?
The bin is overfilling because the shutoff signal isn’t reaching the ice maker: a misplaced bin, a stuck or detached arm, or a failed sensor. Ice piles past the bin and falls out when the door opens. Turn the ice maker off, pick up the ice so no one slips, and work through the checks.
Why does my ice maker keep filling with water?
If water keeps flowing into the tray, or drips with the ice maker switched off, the water inlet valve is probably leaking through. That can freeze the bin into one solid block or send water out of the freezer. Close the supply valve and call; a new valve is typically $170–$300 in LA.
