Hand loading cups into the upper rack of a built-in dishwasher that already holds drinking glasses

Miele Dishwasher F11 and F13 Errors: Drain and Fill Fixes

Short answer: Miele dishwasher F11 is a drain fault: water stays in the tub because the drain pump is blocked or the non-return valve or pump cover over it isn’t seated. F13 means the water inlet is blocked or restricted — a closed valve, clogged inlet filter, kinked hose or low pressure. If cleaning fails, a drain pump typically runs $190–$330 in LA.

This guide is for Miele owners in Los Angeles County and Orange County with F11 or F13 on the display. It covers what Miele’s own support pages say each fault means, how the steps differ between older and newer models, the checks you can do safely, and what repairs cost.

What do F11 and F13 mean on a Miele dishwasher?

F11 means the dishwasher couldn’t drain, so it stopped with water in the wash cabinet. F13 means water isn’t getting in fast enough: Miele describes it as a water inlet that is blocked or restricted. Both are usually cleared with the checks below.

Code What Miele says it means What to check When to call
F11 Drain fault; water left in the wash cabinet Filter combination, non-return valve or drain pump cover, drain pump, drain hose Returns after cleaning, or the impeller won’t turn
F13 Water inlet blocked or restricted Water valve open, inlet filter, hose kinks, water pressure Returns with the valve open and a clean filter
F12, F15 Same description as F13 on Miele’s US site Same checks as F13 Same as F13
F70 Waterproof system has reacted; the program is canceled and the drain pump runs Shut off the water, switch off, unplug Right away

F70 is Miele’s leak protection. Miele’s instruction is to shut off the water, switch the dishwasher off and unplug it, and contact Miele Service — don’t run another program first.

Does the fix depend on your Miele model?

For F11, yes: the meaning is the same, but the part you open is different. Miele publishes two sets of F11 instructions:

Some newer models with a full-text display show a message such as “Water was not pumped away” instead of a code. For F13, the meaning hasn’t changed: Miele’s US site and the older G 1000, G 2000 and G 5000 series manuals we checked all call it a water intake fault, often listed as F12/F13. To know which instructions fit your machine, find the model number — G plus four digits — on the data plate, and match it to your operating instructions.

How do you clear F11?

Bail out the water, clean the filters and the drain pump, and make sure the valve or cover clicks back flush. Miele’s steps, combined:

  1. Switch the dishwasher off and unplug it, or switch off its breaker if you can’t reach the plug.
  2. Remove the lower basket. On G 7000 and G 5000 Discovery models from 2019 on, remove the lower spray arm too.
  3. Lift out the filter combination and scoop the water out with a small container; soak up the rest with a sponge.
  4. Press the catch on the non-return valve or drain pump cover inward, tip it to release it, and rinse it under running water.
  5. With gloves on, check the drain pump opening for foreign objects — Miele warns that glass splinters are hard to see there — and turn the impeller, the small plastic fan inside the pump. It should move with only slight resistance.
  6. Refit the valve or cover until the catch engages and it sits flush, lay the filter combination flat, refit the spray arm, and run a program to check that it drains.
  7. Still F11? Check under the sink for kinks or loops in the drain hose, clean the air gap cap, and run the disposal.

How do you clear F13?

Start with the two simplest causes: a valve that isn’t fully open and a clogged inlet filter. Work through Miele’s F13 checks in order:

  1. Open the water valve under the sink fully.
  2. Clean the inlet filter: switch off and unplug the dishwasher, close the valve, and unscrew the hose connector from the valve. Remove the seal, pull out the small plastic filter with pliers, rinse it, and refit the filter and seal — Miele says the filter must go back in. Screw the connector on, open the valve slowly, and tighten it if it drips.
  3. Straighten any kinks or loops in the inlet hose. A damaged hose must be replaced.
  4. If the flow pressure is below 7.25 psi (0.5 bar), that’s a plumbing issue. Older manuals give a lower minimum, so use the figure in yours.

Safety: on many Miele dishwashers the hose connector’s plastic housing contains an electrical valve. Miele warns of electric shock — never dip that housing in water.

That inlet filter is a fine screen, so grit after a building or street water shutoff, or scale in hard-water areas like much of Southern California, can clog it. Our hard water and dishwashers guide covers prevention.

What does a Miele drain or fill repair cost?

When cleaning doesn’t clear the fault, it’s usually one part. Our dishwasher diagnostic is $69 — trip, testing and a written quote — and it’s applied to the repair when you approve it. Typical Los Angeles County and Orange County prices, parts and labor, with the same fees in both counties and no travel charge:

  • Drain pump: $190–$330
  • Inlet valve: $170–$300
  • Control board: $260–$560
  • Inlet hose or leak-protection hose: priced after diagnosis

Miele parts may need to be ordered, which can mean a second visit. Because a comparable new Miele costs well above a mainstream dishwasher, a pump or valve repair usually passes the 50% rule easily: repair when the quote is under half the price of a comparable new unit and the machine has life left. If your Miele is still under warranty, call Miele first.

When should you call a technician?

Call when F11 comes back after cleaning, the impeller won’t turn or is cracked, F13 persists with the valve open and the filter clean, the hose is damaged, or F70 appears. Calls placed before noon are usually seen the same day across Los Angeles County and Orange County; later calls are typically next business day. Call (866) 696-7767 or book online, and see our dishwasher repair service for what we fix.

No code, just standing water? Our guide to a dishwasher not draining covers every brand, and Bosch owners can use our Bosch E24 and E15 guide.

Frequently asked questions

Can I reset a Miele dishwasher F11 fault?

Switching the dishwasher off and on clears the display, but F11 returns until the drain path is clear. Clean the filter combination, the non-return valve or drain pump cover and the drain pump, then run a program. If F11 comes back, the pump itself or the drain hose is the likely problem.

Why is there water in my Miele dishwasher with F11?

F11 means the dishwasher couldn’t pump the water out, so it stopped with water in the wash cabinet. Scoop it out with a small container before cleaning the filters and the drain pump, and wear gloves: Miele warns that glass splinters are hard to see in the pump.

Is F13 the same on every Miele dishwasher?

Its meaning is. Miele’s US support site lists F12, F13 and F15 as a blocked or restricted water inlet, and older G 1000, G 2000 and G 5000 series manuals list F12/F13 as a water intake fault. The checks are the same: valve open, clean inlet filter, no hose kinks and enough water pressure.

Where is the inlet filter on a Miele dishwasher?

In the connector where the inlet hose screws onto the water valve under the sink. Close the valve, unplug the dishwasher, unscrew the connector, remove the seal and pull the small plastic filter out with pliers. Rinse it and put it back — Miele says it must be reinstalled.

How much does a Miele dishwasher repair cost in Los Angeles?

Our dishwasher diagnostic is $69 and is applied to the repair if you approve it. A drain pump typically runs $190–$330 and an inlet valve $170–$300 in Los Angeles County and Orange County, parts and labor included. Miele parts may need to be ordered, and the exact price is written before any work starts.

About the author — Emanuel “Manny” Misayeledis is the owner and lead technician of Pros Fix Appliances in Glendale (California BHGS registration A49955). He and his team repair residential and built-in appliances across Los Angeles County and Orange County. Last updated: November 3, 2026.

Scroll to Top