Short answer: A Maytag washer leaking from the bottom usually traces to one of four places: the fill hoses or inlet valve (water during fill), the drain pump or drain hose (water during drain), the door boot on a front-loader (water during wash), or the tub seal (water during spin, often with a roar). Shut both water valves first. Most repairs cost $170–$420 in Los Angeles.

Check the likely cause and the price

This guide is for owners of Maytag top-load and front-load washers who have found water under the machine. Maytag washers are built by Whirlpool Corporation, so they share layouts and parts with Whirlpool models, and the same tracing method works on both. For every brand, see our general guide to a washing machine leaking from the bottom.

What should you do first?

  1. Close both water valves behind the washer. A split supply hose is fed at full house pressure until you do.
  2. Unplug the washer. If water has reached the outlet or the cord, switch off the breaker first.
  3. Dry everything: the floor, the hoses and the bottom edge of the cabinet, so new water shows clearly.
  4. In a condo or apartment, tell the manager or the neighbor below now. Water travels farther than it looks.

Why is my Maytag washer leaking from the bottom?

Water runs down inside the cabinet and pools underneath, so the puddle's location says less than its timing. Run a small load, stay with the washer and note the moment water appears.

When water appearsWhere to lookLikely causeTypical LA price
Even with the washer offWall valves and hose ends behind the washerLoose fitting, worn hose washer or a split fill hoseHoses: do it yourself; a leaking wall valve is plumbing work
Only while it fillsBack of the cabinet, below the hose connectionsCracked or leaking water inlet valve$170–$300
During fill or wash, from the frontDetergent drawer or the top of the tubClogged dispenser, too much detergent or an oversized loadFree
During wash (front-load)Under the doorTorn door boot, or something caught in its fold$220–$420 for a boot
Only while it drainsBottom front (pump) or behind the washer (drain pipe)Drain pump, its hoses or filter cap, or a standpipe that overflows$190–$340 for a pump; drain clogs are a plumber's job
During spin, often with a roar and rusty waterUnder the middle of the tubTub seal, usually with worn bearings$450–$750

Where do Maytag top-loaders leak?

On a top-loader the drain pump sits low at the front or underneath, so a drip from the pump or its hoses shows up as a puddle at the front that appears during drain. A sock or coin in the pump can crack its housing.

Splashing is the other top-load leak. High-efficiency top-loaders without a tall agitator use a low wash plate, and a load packed above the top row of holes in the basket can push water over the tub ring during wash. If the leak only happens with bedding or a stuffed load, wash smaller loads before suspecting a part.

A leak under the center of the machine that gets worse on spin is the tub seal. On many top-loaders the seal and bearing live in the gearcase or hub underneath, and that's a larger repair.

Where do Maytag front-loaders leak?

Start with the door boot, the rubber gasket between the door and the drum. Pull back its lower fold and look for a tear, a bra wire or a small sock, and wipe away the gray residue that keeps the door from sealing.

Next is the drain pump filter behind the small cover at the bottom front. A filter cap that was cleaned and screwed back crooked drips on every drain. Then suds: front-loaders use very little water, so too much detergent, or detergent without the HE mark, turns into foam that pushes out of the dispenser and the door. A Sud or Sd message on the display is the washer telling you the same thing (Maytag's explanation of the code).

The fill hoses apply to both types. Whirlpool's installation instructions say to replace inlet hoses every 5 years, and a hose with a bulge or rust at the fitting should go today.

What does a Maytag washer leak cost to fix?

RepairTypical LA price
Water inlet valve$170–$300
Drain pump$190–$340
Door boot (front-load)$220–$420
Tub bearing and seal$450–$750

Prices include parts and labor. The washer diagnostic is $69 and is applied to the repair you approve; fees are the same across Los Angeles, Orange and Ventura counties, with no travel charge. We're an independent repair company, not a Maytag service center, and we use OEM parts whenever they're available; see our Maytag repair page.

Repair or replace? Valves, pumps and boots almost always pass our rule: repair when the quote is under half the price of a comparable new washer and the machine has life left, roughly 10–12 years. A tub bearing and seal is the one to weigh on an older washer.

When should you call?

Call when the leak continues after the hose and loading checks, when water appears under the middle of the tub, or when you can't tell where it starts. Leave the valves closed until then. Call (866) 696-7767 or book online. Calls placed before noon are usually seen the same day, and our line is answered around the clock, with after-hours dispatch for active leaks. We repair washers across the area, including Pasadena and the foothill cities; more on our washer repair page.

Frequently asked questions

Is it safe to use a Maytag washer that is leaking?

No. Close both water valves and unplug it until you know the source. A small drip from a fill hose can become a burst hose, and water near the outlet or cord is an electrical hazard. In a condo or upstairs laundry, even a slow leak can damage the unit below.

Why does my Maytag washer leak only when it drains?

Water that appears only during drain comes from the drain side: the pump, its hoses, a filter cap that isn't seated on a front-loader, or the house drain pipe overflowing behind the washer. If water spills out of the top of the drain pipe, the clog is in the house plumbing.

Why does my Maytag top-load washer leak during the wash cycle?

Usually an oversized load or too many suds. Loads packed above the top of the basket can push water over the tub ring, and extra detergent makes foam that escapes. Wash a smaller load with HE detergent. If it still leaks with a small load, have the tub seal and hoses checked.

How much does it cost to fix a leaking Maytag washer?

In Los Angeles, a water inlet valve typically costs $170–$300, a drain pump $190–$340 and a front-load door boot $220–$420, parts and labor included. A tub bearing and seal runs $450–$750. The $69 diagnostic is applied to the repair you approve.

What's your washer doing?

Still leaking? Call before noon and we can usually be there today.

Appliance Washer
What's the washer doing?
Diagnostic
$69applied to the repair
Same-day
Call before noonMost LA, OC & Ventura calls seen today
Warranty
30–90 daysparts and labor
Registered
BHGS A49955insured, independent

Emanuel “Manny” MisayeledisOwner of Pros Fix Appliances in Glendale (California BHGS registration A49955). Repairs residential and built-in appliances across Los Angeles, Orange and Ventura counties, including the luxury residences and senior-living communities the company services.