Short answer: The most common LG washer error codes are OE (won’t drain), IE (won’t fill), UE (unbalanced), dE (door or lid won’t lock), LE (motor locked), PE (water-level sensor) and FE (too much water). Clear the cause and restart. If the code returns, book a technician: a Pros Fix Appliances washer diagnostic in Los Angeles is $69.
This guide is for LG washer owners in Los Angeles and Orange County looking at a two-letter code. Every meaning below comes from LG’s own support pages, with the checks you can safely do yourself, where front-load and top-load models differ, and what repairs typically cost here.
What do LG washer error codes mean?
Most LG washer error codes point to one of five things: drain, water supply, balance, the door or lid lock, or a sensor. The table follows LG’s washer error code list; the last column is what usually fails when the code keeps coming back, with typical Los Angeles parts-and-labor prices.
| Code | What LG says it means | What you can check | When to call: likely repair and LA price |
|---|---|---|---|
| OE | Won’t drain (water outlet error) | Clean the drain pump filter (front-load), straighten the drain hose, run Spin Only | Pump silent, or humming with a clean filter: usually the drain pump, $190–$340 |
| IE | Won’t fill: water didn’t reach its level in the time allowed | Open both valves fully, straighten the hoses, clean the inlet screens | Water supply is fine but IE returns: inlet valve, $170–$300 |
| UE / uE | Unbalanced load | Spread the load out, add one or two similar items, level the washer | UE even with a normal load: often worn shocks or suspension rods, $220–$380 |
| dE, dE1, dE2 | Door or lid not closed, or not locking | Push clothes clear of the gasket or lid, close until it clicks, then reset | Still won’t lock: door or lid lock, $160–$300 |
| LE (and LE1) | Motor locked or overloaded; the tub can’t turn | Power off, remove some laundry, look for a coin or object in the drum | Returns with a light load: motor, sensor and wiring tested; priced after diagnosis |
| CE | Motor over-current | Unplug for 10 seconds, then try a cycle | If it persists, LG says shut the water tap, unplug and get service |
| PE | Pressure error: the water-level sensor can’t read the level | Unplug 15 seconds, hold Start/Pause 5 seconds, reconnect | Returns: sensor or its wiring; priced after diagnosis |
| FE | Too much water in the tub | Shut both water valves, run Spin or Drain, unplug | Call if it repeats; LG points to the inlet valve, $170–$300 |
| tE | Heating or water-temperature sensor error | Unplug 10 seconds, run a No Spin drain, start a new cycle | Returns: sensor or wiring; priced after diagnosis |
| Sud | Too many suds; LG says the suds-reducing routine adds about 2 hours | Use HE detergent, no more than the recommended dose; run Tub Clean | Rarely a repair |
| PF | Power was interrupted during the cycle | Restart the cycle; check the plug and breaker | Repeats with no outage: outlet and cord checked |
| CL | Child (control) lock is on — not an error | Hold the Control Lock button, or the two buttons marked for it, for 3 seconds | Not a repair |
Three displays aren’t faults: tCL is a Tub Clean reminder, Cd means cool-down on washer-dryer combos, and dr on some top-loaders means it is draining after sitting idle.
Do LG error codes differ between front-load and top-load washers?
Yes. OE, UE, dE, LE, IE and FE flag the same problem on both designs, but where you look and what you do differ, so check which type you have first.
| Code | LG front-load washers | LG top-load washers |
|---|---|---|
| OE | Drain pump filter behind the small cover at the bottom left; clean it first | LG’s steps include no filter: check the hose, run Spin Only. Shows after 13 minutes without draining |
| UE | You fix it: pause, redistribute, load about two-thirds of the drum | Lowercase uE means the washer is rebalancing itself (up to 3 tries); capital UE means it gave up |
| dE | Door: dE1 not closed, dE2 closed but not locking | Lid not closed or locked; it won’t spin until the lid locks. On the SideKick pedestal washer, dE1/dE2 mean the drawer and dE3 the lid |
| LE | Overloaded or locked motor; LG says let it rest 30 minutes | LG points to a coin caught between the tub and washboard; AE is the gear that turns the tub, E6 the clutch |
| IE | A drain hose set too low or sitting in water can siphon the fill away | LG lists a required water pressure of 14.5–116 psi |
| FE | LG’s guide for its WashTower (a front-loader): use the right HE dose, clean the drain filter | Water level too high, possibly a faulty inlet valve; shut the water off |
Read UE carefully on a top-loader: a lowercase uE needs no action, and LG’s top-load UE page says a capital UE on an empty Rinse and Spin cycle means the washer needs repair.
What can you safely check yourself?
Many OE, IE, UE and dE codes clear with free checks. Before opening any cover, unplug the washer. If water is on the floor near the outlet, switch the washer’s breaker off first and don’t touch the plug. Wash water can be hot, so let it cool before draining.
OE on a front-loader: clean the drain pump filter
The tell: you hear the pump humming but the water doesn’t drop. The pump runs but something blocks it; silence suggests the pump itself has failed.
- Unplug the washer and lay towels and a shallow pan in front of it.
- Open the small access cover at the bottom left of the front panel; on the washer in this post’s photo (right), it’s the small square cover.
- If your model has a short drain tube, pull it out, remove its cap and let the water run into the pan, emptying the pan as needed.
- Twist the filter cap off slowly and clear the lint, coins and hairpins. LG suggests a toothbrush.
- Refit the cap hand-tight, plug in and run Spin Only. If the filter was already clean, use less detergent; heavy suds also make the pump lose suction.
LG recommends cleaning this filter at least once a month (LG’s front-load OE steps).
IE and FE: the water supply
Turn both valves behind the washer fully counterclockwise and straighten any kinked hose. To clean the inlet screens, shut the valves, disconnect each hose at the washer, pull the screen out with pliers and scrub it with a toothbrush. With FE, do the opposite: shut both valves first and keep them off until the washer is repaired.
UE and dE: load, level and latch
Spread the laundry evenly, take out single bulky items such as rugs or pillows, and rock the washer corner to corner; if it moves, adjust the legs on that side. For dE codes, push clothes away from the door gasket or lid, close it until it clicks, then reset: unplug, hold Start/Pause for 5 seconds, plug back in.
When should you call a technician?
Call when the same code returns after these checks, when FE appears, or when you smell burning, see sparks or the breaker trips. A code that keeps returning has found a real fault; more resets won’t fix it.
Calls placed before noon are usually seen the same day across Los Angeles County and Orange County. Our washer diagnostic is $69, applied to the repair you approve, with the same fees in both counties and no travel charge. The 50% rule applies: repair when the quote is under half the price of a comparable new washer and the washer has life left; mainstream washers last roughly 10–12 years. Pros Fix Appliances is an independent repair company, not an LG-authorized service center, and we use OEM LG parts whenever available; if your washer is still under LG’s warranty, request service through LG first.
Have the model number from the washer’s label and the code ready, then call (866) 696-7767 or book online. More help: why a washer won’t spin, why a washer won’t fill and common LG appliance problems, or see our washer repair service.
Frequently asked questions
How do I reset my LG washer after an error code?
Turn the washer off, unplug it or switch off its breaker, press and hold Start/Pause for 5 seconds, then restore power and start a new cycle. LG gives this reset for door codes and a similar one for PE. It clears an electronic glitch, not a clogged filter, failed pump or bad sensor.
Why does my LG washer show UE with a small load?
A few heavy items can’t spread evenly around the drum, so the washer can’t balance them. LG suggests adding one or two similar items. If an empty top-loader still shows UE on a Rinse and Spin cycle, LG says it needs repair; on any LG washer we check the leveling, suspension and balance sensing.
Is an FE code on an LG washer an emergency?
Treat it as one. FE means there is more water in the tub than there should be, and LG says a faulty inlet valve can cause it. Turn off both water valves behind the washer, drain it with a Spin or Drain cycle, and leave it unplugged until it’s repaired.
Is it worth repairing an LG washer that keeps showing codes?
Usually, when the fault is a drain pump ($190–$340), door lock ($160–$300) or inlet valve ($170–$300). A main control board ($280–$560) or tub bearing ($450–$750) on an LG washer past about 10 years is where replacing often wins. The technician tells you which at the diagnostic.
