White LG front-load dryer and washer pair in a laundry room with a utility sink

LG Dryer Not Heating? 4 Causes and What Each Repair Costs

Short answer: An LG dryer not heating usually has one of four problems: a restricted vent that tripped a safety part (Flow Sense bars or d75–d95 codes), no power at the heater (nP code), a failed element or thermostat (electric), or no gas, a bad igniter or weak valve coils (gas). Most fixes cost $140–$320 in Los Angeles.

This guide is for owners of LG dryers, electric or gas, that tumble but don’t heat. It starts with the setting that makes a working LG feel cold, then decodes LG’s heat and airflow messages, the four causes behind them, and Los Angeles repair prices. For other brands, see our general guide to a dryer not heating.

Rule out Energy Saver first

A working LG dryer can feel cold because of one default setting. LG says Energy Saver is on by default for the Cotton/Normal cycle, and with it on the dryer air-dries without heat for most of the cycle. Press Energy Saver to turn it off for one load; on some models, holding the Energy Saver default button for 3 seconds changes the default. Air Dry never heats.

To test properly, run the empty dryer on Time Dry or Manual Dry at high heat for five minutes and feel the drum. LG’s rule is simple: a warm drum means the dryer is heating. If it’s warm but loads stay damp, the problem is airflow or sensing; see why a dryer takes too long to dry.

What do LG dryer codes mean?

LG dryers report most heat and airflow problems on the display. The meanings below come from LG’s dryer error code list; the checks and the point to call are ours.

Code What LG says it means What you can check When to call
Flow Sense, 2 or 4 bars Exhaust severely restricted Lint filter, duct behind the dryer, outside flaps Bars return after you clear what you can reach
d75, d80, d90, d95 Exhaust duct restricted 75%, 80%, 90% or 95% Same airflow checks; at d90 or d95, stop using it Duct inside a wall or roof needs cleaning
d80 on a gas model Can also mean no gas reaching the dryer Gas valve fully open, line not kinked Valve open, still no heat
nP No current detected at the heater Plug seated in a grounded 240-volt outlet; breaker off 10 seconds Code returns after the reset
PS Improper voltage at the power cord Nothing safe to check; it’s 240-volt wiring Before running it again
gAS (can look like 9A5) The dryer isn’t receiving gas Valve fully open, line not kinked New install: the installer; otherwise a technician
tE1, tE2, tE3 Thermistor (temperature sensor) problem; tE2 usually in cold conditions Power off at the breaker, then on Code comes back
HS Humidity sensor error; the dryer runs about 2.5 hours Wipe the sensor bars in the drum Code comes back

Why is my LG dryer not heating? The four causes

Once settings are ruled out, an LG dryer that won’t heat almost always falls into one of four groups, listed in the order a technician checks them.

1. A restricted exhaust tripped a safety part

Flow Sense bars and d-codes are LG’s warnings that the vent is restricted. Ignore them long enough and the exhaust gets hot enough to open a safety part, such as a thermal fuse or high-limit thermostat, and the heat stops; LG warns a severely restricted exhaust may be unsafe. The fix has two parts: replace the safety part and clear the vent.

2. No power reaches the heater

LG notes that electric dryers use two breakers, and the heater needs both sides of the 240-volt supply. That’s what nP reports: no current at the heater. If seating the plug and a 10-second breaker reset don’t clear it, LG recommends a licensed electrician check the outlet; if the outlet tests good, the fault is inside the dryer.

3. The element or a thermostat failed (electric)

The heating element is a coil of resistance wire that eventually breaks; a broken coil makes no heat and often shows nP, because no current flows. A failed high-limit thermostat or thermal fuse does the same, and the technician measures each part to find the one that opened.

4. No gas, or a failed igniter or valve coils (gas)

On an LG gas dryer, gAS or d80 can mean the supply itself: a valve partly closed after a move, or a kinked flexible line. If gas is reaching the dryer, the burner is next. A broken igniter never glows; weak gas-valve coils let the igniter glow and go dark with no flame, or let the burner light and go out repeatedly.

Ventless LG models don’t vent outside, and heat-pump versions run cooler by design. When they dry poorly, LG points first to the lint filters and the heat exchanger, which need regular cleaning.

How much does an LG dryer repair cost?

Most LG no-heat repairs cost $140–$320 in Los Angeles County and Orange County, parts and labor included. LG parts are model-specific, so the exact price comes in writing after diagnosis.

Repair Model type Typical LA price
Thermal fuse or thermostat Electric and gas $140–$240
Heating element Electric $180–$320
Igniter or gas-valve coils Gas $170–$320
Control board Electric and gas $260–$520

The $69 dryer diagnostic is applied to the repair you approve, with no travel charge across LA County and Orange County. We’re an independent repair company, not an LG service center, and we use OEM LG parts whenever they’re available. For a lint-packed duct, our dryer vent cleaning cost guide explains what a full cleaning involves.

Safe checks for an LG dryer

  1. Turn Energy Saver off and run the five-minute timed test on high, empty.
  2. Write down any code exactly, including Flow Sense bars, before clearing it.
  3. Clean the lint filter, and wipe the humidity sensor bars inside the drum with a damp cloth; LG suggests doing the bars monthly.
  4. Reset the power: switch the dryer’s breaker off for at least 10 seconds, then on.
  5. Gas models: make sure the gas valve is fully open.
  6. Check the exhaust: unplug the dryer, then make sure the duct behind it runs straight or in a gentle S-curve with no crushing, kinks or holes. Outside, the vent flaps should open fully while the dryer runs.

Stop and call if the breaker trips again, you smell burning, PS appears, or water has reached the wiring. Don’t remove panels: electric LG dryers carry 240 volts inside. If you smell gas, leave without touching switches or the dryer, then call SoCalGas at 1-800-427-2200 or 911 from outside.

When to call about an LG dryer

Call when a code returns after these checks, or when the timed heat test stays cold with the airflow clear. Call (866) 696-7767 or book online; calls placed before noon are usually seen the same day across Los Angeles County and Orange County, and later calls typically the next business day. Have the model number from the dryer’s label ready so the right parts come on the first trip.

Repair or replace? Dryers last about 15 years, and our rule is to repair when the quote is under half the price of a comparable new dryer. Fuses, thermostats, elements, igniters and coils pass that test on almost any LG with years left; a control board on an older LG is the case to weigh. More on what we fix is on our dryer repair page.

Frequently asked questions

What does nP mean on an LG dryer?

LG says nP means the dryer detects no current at the heater, so it tumbles without heat. Seat the plug fully in its grounded 240-volt outlet and switch the dryer’s breaker off for at least 10 seconds. If nP returns, have the outlet checked; if it’s good, the heater circuit needs testing.

Can I keep using my LG dryer with a d90 or d95 code?

LG says no: don’t use the dryer until the exhaust has been cleaned and repaired, because a severely restricted exhaust can be unsafe. Clear the lint filter, the duct behind the dryer and the outside flaps. If the code returns, the duct inside the wall or roof needs a professional cleaning.

Why is my LG dryer taking hours but not getting hot?

Check Energy Saver first: LG turns it on by default for Cotton/Normal, and it air-dries without heat for most of the cycle. An HS code also stretches the cycle to about two and a half hours. If a five-minute timed test on high stays cold, look at the four causes.

Will LG fix my dryer under warranty?

If the dryer is still inside LG’s manufacturer warranty, contact LG first, since warranty repairs go through LG. Check your purchase date and warranty terms. Out of warranty, an independent repair company such as Pros Fix Appliances can diagnose and repair it, using OEM LG parts whenever available.

About the author — Emanuel “Manny” Misayeledis is the owner and lead technician of Pros Fix Appliances in Glendale (California BHGS registration A49955). He and his team repair residential and built-in appliances across Los Angeles County and Orange County. Last updated: November 3, 2026.

Scroll to Top