Close-up of a white front-load washer control panel with a chrome program dial and buttons

Whirlpool Error Codes Explained: Washer, Dryer, Dishwasher, Fridge

Short answer: Whirlpool error codes use an F#E# format on most newer models: F is the system, E the fault. The most common are F9 E1 (slow drain), F8 E1 or LF (slow fill), Sd (too many suds), uL (unbalanced load) and AF (restricted dryer vent). Fix the cause, reset the power, and book service if the code returns.

This guide is for Whirlpool owners in Los Angeles County and Orange County with a code on the display. It covers the codes Whirlpool documents on its own support site for washers, dryers, dishwashers and refrigerators, what you can safely check, and when a technician is the next step.

How do you read a Whirlpool error code?

A Whirlpool F#E# code has two parts: the F number points to the function or system, and the E number to the error within it. Digital displays show the code directly. On a dishwasher without a display, the Clean light flashes it: count the first group of flashes (F), wait through a 1–2 second pause, count the second group (E), and the pattern repeats after about 5 seconds. Seven flashes, a pause and one flash is F7 E1, as Whirlpool explains on its dishwasher support page.

The same code can mean different things on different products and model years, so read it against the right table below and check your owner’s manual when a code isn’t listed.

What do Whirlpool washer error codes mean?

Most Whirlpool washer codes mean water is draining or filling too slowly, there are too many suds, the load is unbalanced, or the door won’t lock.

Code Meaning Safe check When to call
F9 E1 (F21 or F02 on some older front-loaders) Long drain, over 8 minutes on front-loaders Straighten the drain hose, clear the standpipe and clean the pump filter if your model has one Code returns (drain pump $190–$340)
F8 E1, LF or LO FL Long fill or low water flow Open both faucets fully, unkink the inlet hoses, remove any anti-flood device in the line Still fills slowly (inlet valve $170–$300)
Sd, Sud or 5d Too many suds Let the suds routine finish; use HE detergent at the right dose and regular liquid bleach, not “no-splash” Suds codes with normal detergent use
uL or OFb Unbalanced load Spread the load, level the washer, pair a single heavy item with towels Normal loads keep going off balance (suspension set $220–$380)
F5 E2 Door not locking (front-load) Make sure nothing blocks the door and it closes fully Code returns (door lock $160–$300)
F7 E1 Motor speed sensing error Confirm the shipping bolts are out and the washer isn’t overloaded Code returns on a normal load

On top-loaders, Whirlpool warns that a drain hose pushed more than about 4.5 inches into the standpipe can siphon water out as the washer fills, which triggers LF. Whirlpool’s front-load code list has the full wording, and LOC on the display is just the control lock, not a fault. Our washer repair page covers the parts behind these codes.

What do Whirlpool dryer error codes mean?

Whirlpool dryer codes mostly point to airflow: AF or Check Vent means the lint screen or vent is restricted, and most other F codes mean the control has found a fault that needs service.

Code Meaning Safe check When to call
AF, Check Vent or F4 E3 Restricted airflow: lint screen or vent clogged, crushed or kinked Clean the lint screen, straighten the duct, clear the outside hood Weak airflow at the hood after that: the vent run needs cleaning
F3 E1 Exhaust thermistor (the exhaust temperature sensor) Breaker off for 1 minute, then run Timed Dry and watch Code returns: the sensor or wiring needs testing
F3 E2 Five loads in a row dried with no moisture-sensor readings Level the dryer, dry fuller loads on an Automatic cycle, press Power to clear Code persists
L2 Low or no line voltage, so the heater can’t come on (electric) Check both household breakers or fuses and the power cord connection Breakers fine and code persists: an electrician checks the circuit
PF A power failure interrupted the cycle Hold Start to restart, or press Power to clear Not needed

Whirlpool’s Check Vent page gives a simple test: run the dryer for 5–10 minutes and hold your hand under the outside hood; airflow weaker than a hair dryer on high means the vent needs cleaning. Our guide to dryer vent cleaning in Los Angeles explains when that takes a professional.

What do Whirlpool dishwasher error codes mean?

Whirlpool dishwasher codes usually mean the dishwasher isn’t draining (F9 E1), has found water in its base (F8 E4), isn’t getting water (H2O), or has a motor or control fault that a power reset doesn’t clear.

Code Meaning Safe check When to call
F9 E1 Long drain: not draining Clean the filter, unkink the drain hose, check that a connected disposal is clear (and its knockout plug is out on a new install), clear the air gap Still won’t drain (drain pump $190–$330)
F8 E4 Water in the drip tray under the tub Turn off power and water; look for leaks at the supply and drain connections Any repeat: the base must be dried and the leak found
H2O Not detecting water Open the supply valve under the sink fully; check the line for kinks Still no water (inlet valve $170–$300)
F7 E2 Wash motor error Cut power for 30 seconds Code returns (wash pump or motor $280–$520)
F6 E1 User interface or main control error Cut power for 30 seconds Code returns (control board $260–$560)

For F9 E1 or standing water, our guide to a dishwasher that isn’t draining goes step by step, starting with the disposal and the air gap. More on the dishwasher repair page.

Whirlpool refrigerator error codes

A flashing F code on a Whirlpool refrigerator means the control has detected a fault. Whirlpool’s support pages give the same first step for these codes rather than a meaning for each, because the meaning depends on the model:

  1. Unplug the refrigerator or switch off its breaker for 1 minute.
  2. Restore power and make sure cooling is turned on.
  3. Watch the display for a minute. If the code returns, schedule service.

Meanwhile keep the doors closed, and move perishables to a cooler with ice if the fresh-food side is warming. These codes usually lead to a sensor, a fan, a defrost part or the control board: fans and defrost parts typically run $190–$360 in Los Angeles and a main control board $280–$620 (see refrigerator repair).

Do Maytag, KitchenAid and Amana use the same codes?

Maytag, KitchenAid, JennAir and Amana are also Whirlpool Corporation brands, and many of their washers, dryers and dishwashers use the same F#E# format. Don’t assume a code means the same thing across brands or model years; check that brand’s manual or support site for your model. Kenmore models with a 110 or 665 prefix were generally built by Whirlpool, as our Kenmore guide explains.

Safe checks for any Whirlpool code

Any Whirlpool code is worth one round of simple checks before you book a visit, as long as you stay outside the cabinet.

  1. Write the code down exactly and photograph the model and serial tag.
  2. Fix the obvious cause from the tables: a kinked hose, a clogged filter or lint screen, a closed faucet, an uneven load.
  3. Reset the power the way Whirlpool specifies: 5 minutes unplugged for a washer, 1 minute at the breaker for a dryer or refrigerator, 30 seconds for a dishwasher.
  4. Run a short cycle and watch. A code that comes straight back is a real fault; repeated resets won’t fix it.

Stop and call if you smell gas (leave without touching switches and call SoCalGas or 911 from outside), smell burning, see water near wiring, or the breaker trips again.

When to call a technician

Call a technician when a Whirlpool code returns after the safe checks, or right away for a leak, a warm refrigerator or a burning smell. If the appliance is still under Whirlpool’s warranty, start with Whirlpool. Pros Fix Appliances is an independent repair company, not Whirlpool-authorized, that repairs Whirlpool, Maytag, KitchenAid and Amana appliances across Los Angeles County and Orange County with OEM parts whenever available.

A drain pump, inlet valve, door lock or sensor is almost always worth fixing on a Whirlpool with years left in it; a control board on an older washer or dishwasher is worth it only if the quote is under half the price of a comparable new unit. Calls placed before noon are usually seen the same day. The diagnostic is $69 for washers, dryers and dishwashers and $85 for refrigerators, applied to the repair you approve. Call (866) 696-7767 or book online.

Frequently asked questions

Why does a Whirlpool error code keep coming back?

A power reset clears the display, not the fault. If a drain, fill or vent code returns after the hose, filter, faucets and vent have been checked, a part such as the drain pump, inlet valve or a sensor has usually failed and needs testing. That’s the point to book a diagnostic rather than keep resetting.

What does F21 mean on a Whirlpool washer?

On some older Whirlpool front-loaders, F21 (and F02) means draining is taking longer than expected. Check the drain hose for kinks or clogs, use only HE detergent at the right dose, then press Pause/Cancel or unplug the washer for 5 minutes. If F21 returns, the drain pump or its filter needs attention.

Is it safe to keep using a Whirlpool appliance that shows an error code?

A washer with a suds or unbalanced-load code is fine once you correct the cause. A dryer showing AF shouldn’t keep running long cycles on a blocked vent, so clean the vent first. Stop using any appliance that smells of burning, trips the breaker or has water near its wiring.

About the author — Emanuel “Manny” Misayeledis is the owner and lead technician of Pros Fix Appliances in Glendale (California BHGS registration A49955). He and his team repair residential and built-in appliances across Los Angeles County and Orange County. Last updated: November 3, 2026.

Scroll to Top