Short answer: A dryer not heating while the drum still turns usually has a blown thermal fuse, a burned-out heating element or one tripped half of its 240-volt breaker (electric), or a failed igniter or weak gas-valve coils (gas). A restricted vent is often what caused it. Most of these repairs cost $140–$320 in Los Angeles.
This guide is for anyone whose dryer tumbles but leaves the clothes cold and damp. It covers electric and gas causes in the order we find them, safe checks and Los Angeles repair prices. LG owners seeing nP, d80 or Flow Sense bars should start with our LG dryer codes and causes.
Confirm it’s a no-heat problem
A five-minute test separates a dryer that makes no heat from one that dries slowly. Run the empty dryer on a timed, high-heat cycle for five minutes and feel the drum, the same test Whirlpool’s troubleshooting uses.
- Cold drum: the dryer isn’t heating. Read on.
- Warm drum, damp loads: the heat works; see why a dryer takes too long to dry.
- Cold on some cycles only: Air Fluff cycles never heat, and some energy-saving modes use little heat.
Then check the type: an electric dryer has a large three- or four-prong plug on a 240-volt double breaker; a gas dryer has a normal plug plus a gas line.
Why is my electric dryer not heating?
An electric dryer that tumbles without heat has lost power to the element, or a part in the heat circuit has opened. We check in this order.
1. Half of the 240-volt circuit is off
Whirlpool explains that one side of the dryer’s 30-amp, 240-volt circuit runs the motor and the other the element, so with one side off the drum turns but the dryer won’t heat. Tell: it started after an outage or a tripped breaker.
2. The thermal fuse has blown
A thermal fuse is a one-time safety switch that opens when the dryer overheats; one common Whirlpool design opens at 196°F. Depending on the model, it kills the heat or stops the dryer from starting. Tell: drying slowed for weeks, then the heat quit, which means the airflow needs fixing too.
3. The heating element has burned out
The element is a coil of resistance wire at the back of the dryer that eventually breaks from years of heating and cooling. Tell: cold air from the first minute while the breaker is fine. If a broken coil trips the breaker at every start, leave it off and call.
4. A thermostat or the control has failed
The high-limit thermostat cuts the heat if the heater housing overheats; the cycling thermostat holds the drying temperature (electronic dryers use a thermistor, a temperature sensor, instead). Either one failing open leaves the heat off. Least common is a control board or timer that stops powering the element, confirmed only after the heat parts test good.
Why does my gas dryer turn but not heat?
A gas dryer that tumbles without heat has a fuel or ignition problem. The burner lights in sequence: the igniter glows orange-hot, a flame sensor detects that heat, then coils on the gas valve open it. Where the sequence stops points to the part.
- Gas off. Whirlpool notes a gas dryer still tumbles with the shutoff valve closed. The valve is open when its handle runs parallel to the pipe.
- Igniter. This brittle ceramic glow bar never glows once broken; cracked, it may light the burner and let it go out repeatedly.
- Gas-valve coils. These small electromagnets open the valve. A weak coil lets the igniter glow, then go dark with no flame, or the burner light and go out over and over.
- Flame sensor. Stuck one way, the igniter never glows; stuck the other, it glows but no gas flows.
Gas dryers have the same thermal fuse and thermostats as electric ones, and a restricted vent opens them the same way.
How much does it cost to fix a dryer that won’t heat?
Most no-heat repairs cost $140–$320 in Los Angeles County and Orange County, parts and labor, on mainstream brands. The exact price is in writing after diagnosis.
| Cause | Type | What you notice | Typical LA price |
|---|---|---|---|
| One side of the 240-volt circuit off | Electric | No heat after an outage | Free if a breaker reset holds |
| Blown thermal fuse | Both | Slow drying, then no heat or no start | $140–$240, plus fixing the airflow |
| Burned-out heating element | Electric | Cold air from the first minute | $180–$320 |
| High-limit or cycling thermostat | Both | No heat, or heat that drops out | $140–$240 |
| Igniter or gas-valve coils | Gas | No glow, or glow with no flame | $170–$320 |
| Flame sensor | Gas | Igniter never glows, or glows nonstop | Quoted at diagnosis |
| Control board or timer | Both | No heat on any cycle; parts test good | $260–$520 |
The $69 dryer diagnostic is applied to the repair you approve, with no travel charge anywhere in LA County or Orange County.
Safe checks to do first
These checks need no tools and no panels off; stop at the first one that explains the problem.
- Breaker (electric): switch the dryer’s double breaker fully off for 10 seconds, then on.
- Gas valve (gas): the handle should run parallel to the pipe. Don’t loosen fittings.
- Lint screen: clean it and hold it under the tap; if water pools on the mesh, wash off the softener film with a soft brush and hot, soapy water.
- Airflow: with the dryer running, the outside flap should open and blow strongly, a check the U.S. Fire Administration also lists.
- Duct: unplug the dryer, slide it out without straining a gas line, and straighten any crushed duct. Replace foil or plastic duct with metal.
Stop and call if the breaker trips again, you smell burning, or water has reached the wiring. Don’t remove panels: electric dryers carry 240 volts inside. If you smell gas, leave without touching switches or the dryer, then call SoCalGas at 1-800-427-2200 (or your gas utility) or 911 from outside, as SoCalGas and the California Public Utilities Commission advise.
Why a clogged vent stops the heat
A restricted vent makes a dryer overheat until a safety part shuts the heat off: hot, wet air backs up, the high-limit thermostat cycles, and eventually the thermal fuse blows. The photo at the top of this guide is from one of our service calls: lint packed around a gas burner and across the cabinet floor.
It’s also a fire risk. The National Fire Protection Association’s dryer safety tip sheet (2016) names failure to clean as the leading cause of home clothes dryer and washer fires. Many LA condos put the laundry closet mid-unit, with a long duct to an outside wall or the roof where lint collects. Our dryer vent cleaning cost guide explains a full cleaning.
When to call, and whether it’s worth fixing
Call (866) 696-7767 or book online when the checks don’t bring the heat back, or right away if a stop sign appears. Calls placed before noon are usually seen the same day across Los Angeles County and Orange County; later calls, typically the next business day.
The $69 diagnostic covers the trip, testing and a written quote, and it’s applied to the repair; if you decline, it’s all you pay. Seniors and veterans get 10% off the repair. Dryers last about 15 years, so by our 50% rule (repair when the quote is under half the price of a comparable new dryer) a $140–$320 fix almost always wins; a $260–$520 board on an old, inexpensive dryer is where replacing can make more sense. More on what we fix is on our dryer repair page.
Frequently asked questions
Can I reset a dryer thermal fuse?
No. A thermal fuse is a one-time safety device that has to be replaced once it opens, typically $140–$240 in Los Angeles with labor. Never bypass it. Find out why it blew, usually a restricted vent, or the new fuse will fail too.
Why does my gas dryer igniter glow but not light?
An igniter that glows and then goes dark without a flame means gas never reached it. The usual causes are weak gas-valve coils, a stuck flame sensor or a closed supply valve. Check the valve handle first; the coils and sensor need a technician’s meter.
Why did my dryer stop heating after a power outage?
An electric dryer needs both sides of its 240-volt supply: one runs the motor, the other the heating element. If one side stays off after an outage, from a breaker that didn’t fully reset, a blown fuse in an older panel or a partial outage, the drum turns but stays cold. Reset the double breaker; if it trips, call.
Is a dryer that won’t heat dangerous to use?
Not by itself, but the cause can be. A fuse that blew because of a lint-packed vent means the dryer was overheating, and a burning smell or a breaker that keeps tripping means stop using it. If a gas dryer smells of gas, leave and call the gas company or 911 from outside.
