Dryer troubleshooting guide

Most dryer problems start with airflow: a lint-packed vent makes drying slow and trips the safety parts that cut the heat. Pick what yours is doing for safe checks for gas and electric dryers, what each error code means and when to stop and call.

Last updated

Troubleshoot your dryer

Add the brand and model number for brand notes and error codes, then pick what it's doing. Nothing you type leaves this page.

Appliance Dryer

Brand-specific steps and error codes, if we know the series.

What's the dryer doing?

Dryer not heating

A dryer that tumbles but won't heat usually has a half-tripped breaker (electric), a closed gas valve (gas) or a blown thermal fuse, and a clogged vent is the usual reason the fuse blew. Fix the vent along with the part.

Most likely, in the order we find it: Heating element or gas igniter, thermal fuse, high-limit thermostat, or a blocked vent.

  1. Stop if you smell gas Gas dryers only

    Gas dryer and a gas smell: don't touch switches or unplug anything. Leave, and call SoCalGas at (800) 427-2200 or 911 from outside.

  2. Reset both breakers Electric dryers only

    Electric dryers use a double breaker (two switches joined together). Switch it fully off, then on. One half can trip and leave the drum turning with no heat.

    If the heat is back, that was it.

  3. Make sure the gas is on Gas dryers only

    Check that the shut-off valve on the gas line behind the dryer is open (the handle in line with the pipe) and that your other gas appliances work.

  4. Clean the lint screen and check the vent

    Clean the lint screen, then go outside while the dryer runs. You should feel strong, warm air at the vent hood and see the flap open.

    Weak air means a clogged vent. It overheats the dryer and blows the safety fuse that cuts the heat.

  5. Test it on a heat cycle

    Run Timed Dry on High for 10 minutes with a few damp towels. Air Fluff, No Heat and some delicate cycles use little or no heat.

    Still cold on High: it needs a repair.

  6. Know what's next

    The usual fixes are the thermal fuse, the heating element or a thermostat on electric dryers, and the igniter or gas valve coils on gas dryers.

    We check the vent on the same visit so the new part doesn't fail again.

Still not working?

What we check
Element or igniter, fuses, thermostats, vent airflow
Typical repair
Thermal fuse / thermostat $140–$240 · Heating element (electric) $180–$320 · Igniter or gas valve coils (gas) $170–$320Parts and labor, typical for LA, OC & Ventura; written quote before any work.
The visit
$69 diagnostic, applied to the repair · Usually fixed on the first visit

Dryer takes too long to dry

A dryer that needs two cycles is almost always short of airflow: lint in the vent run, a crushed duct behind the dryer or a vent flap that won't open. Clothes that come out of the washer dripping add time too.

Most likely, in the order we find it: Restricted vent, moisture sensor, or a cycling thermostat.

  1. Wash the lint screen

    Dryer sheets leave an invisible film. Wash the screen with warm soapy water and a soft brush, rinse it and let it dry.

    Water should run through the mesh, not bead on top.

  2. Check the vent hood outside

    With the dryer running, the flap outside should open fully and the air should feel strong and warm.

    A flap that barely moves means lint is packed in the duct.

  3. Straighten the duct

    Ease the dryer back so the duct behind it isn't crushed or kinked. Replace plastic or foil accordion duct with semi-rigid metal duct.

    A crushed duct can double the drying time.

  4. Spin the clothes well first

    If clothes come out of the washer dripping, run an extra spin, and check that the washer drains properly.

  5. Don't overload it

    Fill the drum about half to two-thirds full so clothes can tumble.

  6. Have the vent run cleaned

    Long vent runs collect lint you can't reach from either end. A vent cleaning restores the airflow and lowers the fire risk.

    If airflow at the hood is strong and drying is still slow, a heating part or thermostat may be weak. Call.

Still not working?

What we check
Vent back-pressure, sensor bars, cycle timing
Typical repair
Thermal fuse / thermostat $140–$240Parts and labor, typical for LA, OC & Ventura; written quote before any work.
The visit
$69 diagnostic, applied to the repair · Usually same-day

Dryer won't start or tumble

A dryer that won't start usually has a tripped breaker, a door that isn't latching, the control lock on, or a Start button that needs holding. If it hums but the drum won't turn, the belt or the motor has failed.

Most likely, in the order we find it: Door switch, belt, start switch, motor or control board.

  1. Check the power

    Electric dryers use a double breaker: switch it fully off, then on. Gas dryers plug into a regular outlet: test it with a lamp.

  2. Close the door firmly

    Most dryers won't start unless the door switch clicks. Check for clothes caught in the door.

  3. Hold Start and check the lock

    Many dryers need Start held for 2–3 seconds, and won't start with Control Lock on. A lock icon means hold the lock button for 3 seconds.

  4. Listen when you press Start

    A hum without tumbling means a broken belt or a stuck motor: unplug it and call. No sound at all usually means a thermal fuse, the door switch or the control.

    Don't keep pressing Start on a humming dryer, because the motor can overheat.

Still not working?

What we check
Switches, belt, motor, drum rollers
Typical repair
Belt, rollers and idler kit $190–$340 · Motor $280–$480Parts and labor, typical for LA, OC & Ventura; written quote before any work.
The visit
$69 diagnostic, applied to the repair · Usually same-day

Dryer banging, squealing or thumping

Dryer noise usually comes from something loose in the drum, worn drum rollers or an idler pulley, or a worn drum glide. A squeal or thump gets worse over time and can snap the belt, so it's worth fixing early.

Most likely, in the order we find it: Drum rollers, idler pulley, belt or glides.

  1. Empty the drum and the pockets

    Coins, zippers, shoes and buttons bang and rattle. Check the drum and the lint screen slot.

  2. Name the sound

    A squeal is usually the drum rollers or the idler pulley. A thump is a flat spot on a roller or a loose drum. Scraping is a worn drum glide or something caught between the drum and the front.

    Telling dispatch which sound it is helps the technician bring the right kit.

  3. Level the dryer

    Push on opposite corners: it shouldn't rock. Adjust the legs until it sits firmly.

  4. Call before it gets worse

    Roller, pulley and belt kits are usually replaced in one visit.

Still not working?

What we check
Rollers, pulley, bearing wear
Typical repair
Belt, rollers and idler kit $190–$340Parts and labor, typical for LA, OC & Ventura; written quote before any work.
The visit
$69 diagnostic, applied to the repair · Usually same-day

Dryer shuts off early or overheats

A dryer that stops early or gets too hot is usually overheating from poor airflow, or its moisture sensor is reading the clothes as dry. Clean the vent and the sensor bars before suspecting a part.

Most likely, in the order we find it: Overheating from a clogged vent, a thermostat or a sensor.

  1. Clean the lint screen and the vent

    Overheating trips the safety thermostat and ends the cycle. Clean the screen and make sure air blows strongly at the outside flap.

  2. Wipe the moisture sensor bars

    Find the two metal strips inside the door opening and wipe them with a soft cloth and rubbing alcohol. Fabric softener film makes them read dry too soon.

    Sensor cycles run to the end again.

  3. Try Timed Dry

    Sensor cycles end when the clothes feel dry to the sensor, so small loads can end early. Timed Dry runs the full time.

  4. Feel the cabinet

    If the top or sides are too hot to touch, stop using the dryer.

    Something is overheating. Call before you run it again.

Still not working?

What we check
Vent, thermostats, sensor
Typical repair
Thermal fuse / thermostat $140–$240Parts and labor, typical for LA, OC & Ventura; written quote before any work.
The visit
$69 diagnostic, applied to the repair · Usually same-day

Burning smell from the dryer

A burning smell from a dryer means lint is scorching near the heater or burner, or the motor or belt is overheating. Stop the dryer, cut the power and don't use it until it's checked, because this is how dryer fires start.

Most likely, in the order we find it: Lint around the heater or burner, a failing motor or belt, or a blocked vent.

  1. Stop it and cut the power

    Stop the dryer and switch it off at the breaker or unplug it. If you see smoke or flames, get everyone out and call 911.

  2. Keep the door closed

    Let the dryer cool with the door shut. Opening it can feed a smoldering fire with air.

  3. Rule out new-dryer smell

    A new dryer, or one with a newly replaced heater, can smell for the first few loads. Anything stronger, or a plastic, rubber or electrical smell, needs a technician.

  4. Call before using it again

    A technician clears lint from around the heater or burner, checks the motor and belt, and checks the vent.

Still not working?

What we check
Heater area, motor, belt, vent
Typical repair
Motor $280–$480Parts and labor, typical for LA, OC & Ventura; written quote before any work.
The visit
$69 diagnostic, applied to the repair · Usually same-day

Dryer error codes by brand

What the code on the display means and what to try first. Codes vary by model and year: if your owner's manual says something different, it wins. If the code comes back after one reset, call with the code and the model number.

Samsung dryer error codes

Samsung dryer error codes
CodeWhat it meansWhat to try first
9C1, 9E, 2E, 9E1Power supply problemMake sure the dryer has its own outlet, no extension cord, and that both breakers are on. Steps: dryer won't start or tumble
tS, t5, tC, tO, t0, tE, tE3, tC5, tCS, 1 tCTemperature or sensor problem, usually a clogged lint screen or vent trapping heatClean the lint screen and the vent run. Steps: dryer shuts off early or overheats
HC, hE, HC4, 1 HCHeating problem: the dryer is getting too hotClean the lint screen and the vent; call if it returns. Steps: dryer shuts off early or overheats
dC, dEDoor openClose the door firmly and check for clothes caught in it. Steps: dryer won't start or tumble
bE, bE2, bC2, 6E, 6E2A button is stuckPress each button firmly to free it.
3C, 3EMotor problemRestart the cycle once; call if it returns. Steps: dryer won't start or tumble

Source: Samsung US: dryer displays an error code

LG dryer error codes

LG dryer error codes
CodeWhat it meansWhat to try first
d75, d80, d90, d95Vent restricted (the number is roughly how blocked it is)Clean the lint screen and the vent run, and check the outside flap. Steps: dryer takes too long to dry
nPNo power reaching the heater (electric dryers)Reset both breakers: the heater needs the full 240 volts. Steps: dryer not heating
tE1, tE2, tE3Temperature sensor errorUnplug it for a minute; call if it returns. Steps: dryer not heating
dEDoor openClose the door firmly. Steps: dryer won't start or tumble
PFThe power was interruptedRestart the cycle.

Source: LG USA: dryer error code list; LG USA: understanding d90 and d95 error codes · More detail: LG Dryer Not Heating? Codes, Causes and LA Repair Costs

Whirlpool and Maytag dryer error codes

Also KitchenAid, JennAir and Amana, which use the same F#E# codes: F is the system, E the fault.

Whirlpool and Maytag dryer error codes
CodeWhat it meansWhat to try first
AF, Check Vent, F4 E3Restricted airflow: lint screen or vent clogged, crushed or kinkedClean the lint screen, straighten the duct and clear the outside hood. Steps: dryer takes too long to dry
F3 E1Exhaust temperature sensorSwitch off the breaker for 1 minute, then run Timed Dry; call if it returns. Steps: dryer not heating
F3 E2Moisture sensor got no readings for several loadsLevel the dryer, dry fuller loads on an Automatic cycle and wipe the sensor bars. Steps: dryer shuts off early or overheats
L2Low or no line voltage, so the heater can't come on (electric dryers)Check both breakers or fuses and the cord connection. Steps: dryer not heating
PFThe power was interruptedHold Start to restart, or press Power to clear it.

Source: Whirlpool: error codes in dryers; Whirlpool: AF or Check Vent, dryer · More detail: Whirlpool Error Codes: Washer, Dryer, Dishwasher, Fridge

Where's the model number on a dryer?

It's on a sticker called the rating label, and you can reach it without tools. The model number tells the tool above (and our technician) which series you have; the serial number on the same label holds the build date. Watch 0 and O, 1 and I, 8 and B.

  • Open the door.
  • Look here first: On the frame around the door opening, at the top or on a side.
  • Then check: The back panel. Look over the top or from the side.
  • Read the line marked Model (Mod., M/N or Model No.), not Serial (Ser., S/N). Copy every character, including anything after a dash or slash.

Don't pull out a gas dryer to read the back: moving it strains the gas connector.

Can't find the label?
  • Check the owner's manual, the receipt, the delivery paperwork or the registration card.
  • If it's connected to the brand's app, the model number is in the app's device information.
  • Can't read it? Take a photo with the flash off, holding the phone at a slight angle so it doesn't glare, then zoom in.
  • Still nothing? Skip it. The guide works without a model number, and our technician will find it at the visit.
How dryer model numbers start, by brand
BrandModel number starts with
AmanaNED: electric dryer · NGD: gas dryer
BoschWTG, WTW, WQB: compact electric dryer
ElectroluxEFME, ELFE: electric dryer · EFMG, ELFG: gas dryer
Fisher & PaykelDE: electric dryer
FrigidaireFLCE: laundry center (electric dryer) · FLCG: laundry center (gas dryer) · FFRE, FAQE, FFQE: electric dryer · FFRG, FAQG, FFQG: gas dryer
GEGTD, GFD, GTX, PFD (E): electric dryer · GTD, GFD, GTX, PFD (G): gas dryer
LGWKE: WashTower with an electric dryer · WKG: WashTower with a gas dryer · DLE, DLEX: electric dryer · DLG, DLGX: gas dryer · DLHC: heat-pump dryer
MaytagMED: electric dryer · MGD: gas dryer
MieleT, TWB, TXI: electric dryer
SamsungWD: washer-dryer combo · DVE: electric dryer · DVG: gas dryer · DV…E: electric dryer · DV…G: gas dryer · DV: dryer
Speed QueenDC, DR, DF … E: electric dryer · DC, DR, DF … G: gas dryer · ADE, SDE, LDE: electric dryer · ADG, SDG, LDG: gas dryer
WhirlpoolWED: electric dryer · WGD: gas dryer

The full guide to finding a model number

Brand notes

  • LG. LG dryers show d75 to d95 (or light the Flow Sense bars) as the vent clogs, and nP when no power reaches the heater, usually a half-tripped breaker. LG dryer not heating
  • Whirlpool, Maytag, KitchenAid, JennAir, Amana and Roper. Whirlpool, Maytag, KitchenAid, JennAir and Amana use the same F#E# codes: F is the system and E the fault. Whirlpool error codes explained
  • Kenmore. Kenmore appliances are built by other makers, and the three digits before the dot in the model number say which: 110 is Whirlpool laundry, 795 LG refrigerators, 253 Frigidaire refrigerators and freezers. Error codes follow that maker. Kenmore appliance repair

Questions people ask

How often should a dryer vent be cleaned?

Clean the lint screen after every load and have the vent run cleaned about once a year, sooner if drying takes more than one cycle or the outside flap barely opens. A clogged vent is the most common reason a dryer stops heating, and built-up lint is a fire risk.

How much does dryer repair cost in Los Angeles?

Most dryer repairs we do in Los Angeles, Orange and Ventura counties run $140–$520 for parts and labor, for example thermal fuse / thermostat $140–$240 and heating element (electric) $180–$320. The diagnostic is $69, applied to the repair, and you get a written quote before any work starts.

Is it worth repairing my dryer?

Usually, while the repair costs less than half the price of a comparable new dryer and it has life left. Most dryers last 13–15 years, and premium brands 15–20. Past that age, or when the quote passes half the new price, replacing it is usually the better buy, and we'll tell you so.

Checked everything? Call before noon for a same-day visit.

Dispatch answers the phone and the technician arrives with the likely parts. $69 diagnostic, applied to the repair. Written quote before any work.

Call (866) 696-7767 Book online Mon–Fri 9 am–5 pm · Sat 10 am–2 pm · Emergency calls answered 24/7 · Calls before noon are usually seen the same day

The State of California's record for A49955

California DCA license search record: Household Goods and Services, Bureau of — Licensing details for 49955. Name: Pros Fix Appliances LLC. License type: Major Appliance Repair. License status: CLEAR. Address: 1201 N Pacific Ave #202, Glendale CA 91203, Los Angeles County. Issuance date July 11, 2023. Expiration date July 31, 2027. Current date November 6, 2026.
What the state's license search shows for Pros Fix Appliances LLC, as checked on Nov 6, 2026: status CLEAR, registered since July 11, 2023, valid through July 31, 2027. The live record is one click away — open it on search.dca.ca.gov ↗.