Oven and range troubleshooting guide
Most oven problems are a worn igniter on gas models, a burned-out element on electric ones, or a setting such as a timer or control lock. Pick what yours is doing for safe checks for gas and electric ranges, what the error codes mean and when to stop and call.
Last updated
Troubleshoot your oven
Add the brand and model number for brand notes and error codes, then pick what it's doing. Nothing you type leaves this page.
Brand-specific steps and error codes, if we know the series.
Can't find the label?
- Check the owner's manual, the receipt, the delivery paperwork or the registration card.
- If it's connected to the brand's app, the model number is in the app's device information.
- Can't read it? Take a photo with the flash off, holding the phone at a slight angle so it doesn't glare, then zoom in.
- Still nothing? Skip it. The guide works without a model number, and our technician will find it at the visit.
Oven not heating
An oven that won't heat usually has a worn igniter (gas), a burned-out bake element (electric), a half-tripped breaker, or a timer, lock or Sabbath setting stopping it. Check the settings first; the parts need a technician.
Most likely, in the order we find it: Bake element or igniter, temperature sensor, thermostat or control board.
-
Stop if you smell gas Gas ovens only
Turn the oven off, don't touch light switches, leave and call SoCalGas at (800) 427-2200 or 911 from outside.
-
Check the clock and settings
After a power outage some ovens won't heat until the clock is set. Cancel any delayed or timed bake, and make sure Sabbath mode and Control Lock are off.
-
Reset both breakers Electric ovens only
Electric ranges use a double breaker. Switch it fully off, then on: a half-tripped breaker can leave the display on with no heat.
-
Look at the bake element Electric ovens only
With the oven cold and off, look at the bottom element if you can see it. A break, a blister or a bright spot while heating means it has failed.
Elements hidden under the oven floor are tested by the technician.
-
Watch the igniter Gas ovens only
Set Bake to 350°F and look through the slots in the oven floor or the broiler drawer. The igniter should glow orange and the burner should light within about 90 seconds.
Glowing but no flame after about 90 seconds usually means a weak igniter.
-
Try the broiler
If the broiler heats but Bake doesn't, the bake element or the bake igniter is the fault.
If neither heats, the control, a thermal fuse or the gas valve is next.
Still not working?
- What we check
- Element or igniter draw, sensor resistance, board relays
- Typical repair
- Bake or broil igniter $170–$320 · Bake or broil element $180–$340Parts and labor, typical for LA, OC & Ventura; written quote before any work.
- The visit
- $69 diagnostic, applied to the repair · Usually fixed on the first visit
Read: Oven Igniter Not Lighting? Signs, Tests and LA CostGo through these steps one at a time
Oven or range won't turn on
A range that's completely dead usually has a tripped breaker, a loose plug or the control lock on. A dark display with power at the outlet means the control board, an internal fuse or the wiring needs a technician.
Most likely, in the order we find it: Power at the outlet or breaker, a thermal fuse, the control board or the display.
-
Check the breaker
Electric ranges use a double breaker, and gas ranges plug into a regular outlet. Switch the breaker off and on, or test the outlet with a lamp.
-
Turn off Control Lock
A lock icon or LOC on the display means the controls are locked: hold the lock pad (often marked, sometimes Self Clean) for 3 seconds.
-
Reset it
Switch it off at the breaker (or unplug it) for 1 full minute, then switch it back on.
Still dark: call. Don't keep resetting a breaker that trips again.
Still not working?
- What we check
- Supply voltage, fuse, board and display
- Typical repair
- Oven relay or control board $280–$650Parts and labor, typical for LA, OC & Ventura; written quote before any work.
- The visit
- $69 diagnostic, applied to the repair · Usually same-day
Read: Oven Won't Turn On? Causes, Checks and LA Repair CostsGo through these steps one at a time
Oven temperature wrong
An oven that runs hot or cold is often within its normal swing, since most cycle about 25°F around the setting. Check it with an oven thermometer, use the built-in temperature offset, and call if it's off by more than about 50°F.
Most likely, in the order we find it: Temperature sensor, calibration or control board.
-
Measure it
Put an oven thermometer on the middle rack, set 350°F and read it after a 20-minute preheat, then twice more 5 minutes apart.
Average the readings; a single reading catches the swing.
You'll need: Oven thermometer
-
Adjust the offset
Most digital ovens let you adjust the temperature by up to about 35°F in the settings; your manual shows how.
Results should match the recipe afterwards.
-
Take foil off the floor
Foil on the oven floor or covering a rack blocks the heat and causes hot spots.
-
Check the door seal
A torn or flattened door gasket lets heat escape.
Off by more than 50°F, or drifting: the sensor or the control needs testing.
Still not working?
- What we check
- Sensor readings against the set point, calibration
- Typical repair
- Temperature sensor $160–$280Parts and labor, typical for LA, OC & Ventura; written quote before any work.
- The visit
- $69 diagnostic, applied to the repair · Usually same-day
Oven door won't close or unlock
An oven door that stays locked usually just hasn't cooled down after self-clean, which can take more than an hour. A door that won't close or sits crooked has a broken hinge or spring. Never force a locked latch.
Most likely, in the order we find it: Hinges, the door-lock motor, or the gasket.
-
Wait for it to cool
After self-clean the door stays locked until the oven drops to a safe temperature, often an hour or more.
-
Reset the power
Switch the breaker off for 5 minutes, then back on. Many stuck locks release when the control restarts.
-
Don't force the latch
Prying a locked door can break the lock motor or the latch.
-
Check the hinges
If the door won't close, springs open or sits crooked, a hinge or a spring is broken.
Hinges are usually replaced as a pair in one visit.
Still not working?
- What we check
- Hinge alignment, lock assembly, gasket
- Typical repair
- Door hinge or gasket $180–$360Parts and labor, typical for LA, OC & Ventura; written quote before any work.
- The visit
- $69 diagnostic, applied to the repair · Usually same-day
Read: Oven Door Locked After Self-Clean? What to DoGo through these steps one at a time
Range burner won't light
A gas burner that clicks but won't light usually has a wet, dirty or misaligned cap and head, or clogged ports. If no burner clicks at all, check the plug or breaker. If it still won't light after cleaning, the igniter or the valve needs a technician.
Most likely, in the order we find it: Spark module, igniter electrode, gas valve or a clogged burner.
-
Stop if you smell gas
Turn the knobs off. If the smell stays, leave the house and call SoCalGas at (800) 427-2200 or 911 from outside. Don't touch light switches or unplug anything on the way.
-
Listen for the clicks
Turn the knob to Lite: you should hear clicking. If no burner clicks, check the plug and the breaker.
-
Dry and seat the cap and head
When cool, lift off the cap and the burner head, wash and dry them completely, and set the cap back flat and centered.
A cap that sits crooked or wet won't light evenly.
-
Clear the ports
Clear clogged burner ports with a straightened paper clip, not a toothpick, which can snap off inside.
-
Try it again
Most burners light normally once they're dry and seated.
Clicks but no flame after cleaning: the igniter or the burner valve needs a technician.
Still not working?
- What we check
- Spark, electrode, valve, burner ports
- Typical repair
- Igniter electrode or spark module $160–$300Parts and labor, typical for LA, OC & Ventura; written quote before any work.
- The visit
- $69 diagnostic, applied to the repair · Usually same-day
Oven error codes and dead displays
An oven error code is the control reporting a fault, usually a sensor, the door lock, overheating or the keypad. Reset the power once. If the code comes back, the oven needs a repair, and the code plus the model number tell the technician what to bring.
Most likely, in the order we find it: Control board, user interface or power supply.
-
Write the code down
Note the code and when it appears: at preheat, during self-clean or at random.
Type it into the tool above with your brand, or find it in the tables below.
-
Reset once
Switch it off at the breaker (or unplug it) for 1 full minute, then switch it back on.
-
Don't run self-clean to clear it
Self-clean runs the oven very hot and can turn a small fault into a bigger one.
-
Call with the code
Send us the code and the model number. A blank or garbled display is usually the control or the keypad.
Still not working?
- What we check
- Codes, board voltage, display
- Typical repair
- Oven relay or control board $280–$650Parts and labor, typical for LA, OC & Ventura; written quote before any work.
- The visit
- $69 diagnostic, applied to the repair · Usually same-day
Read: GE Oven F Codes: What F1, F2, F3, F7 and F9 MeanGo through these steps one at a time
Oven / Range error codes by brand
What the code on the display means and what to try first. Codes vary by model and year: if your owner's manual says something different, it wins. If the code comes back after one reset, call with the code and the model number.
GE oven error codes
Also GE Profile, Café, Monogram and Hotpoint.
| Code | What it means | What to try first |
|---|---|---|
| F0, F1, F6, F7 | Keypad (touchpad) problem | Reset the power once. Phantom beeps or dead pads point to the keypad. Steps: oven error codes and dead displays |
| F2, F20 | The oven got hotter than its limit | Let it cool fully, then reset once. Steps: oven temperature wrong |
| F3, F4 | Oven temperature sensor | Reset once; the sensor usually needs replacing. Steps: oven temperature wrong |
| F5, F8, FF | Electronic control | Reset once; the control usually needs replacing. Steps: oven error codes and dead displays |
| F9, FC | Door lock circuit | Make sure the door is fully closed and nothing is jammed in the latch. Steps: oven door won't close or unlock |
| F350 | Upper cooling fan circuit, or something blocking the fan | Clear anything blocking the vents. Steps: oven error codes and dead displays |
| FD | Meat probe or its socket | Unplug the probe and try a cycle without it. Steps: oven error codes and dead displays |
Source: GE Appliances: range and wall oven error, fault or function codes · More detail: GE Oven F Codes: What F1, F2, F3, F7 and F9 Mean
Where's the model number on a oven?
It's on a sticker called the rating label, and you can reach it without tools. The model number tells the tool above (and our technician) which series you have; the serial number on the same label holds the build date. Watch 0 and O, 1 and I, 8 and B.
Ranges and stoves
- Pull out the storage or warming drawer at the bottom. Let the oven cool first.
- Look here first: On the frame behind the drawer, on the left or right side.
- Then check: The frame around the oven opening with the door open, or under the control panel.
- Read the line marked Model (Mod., M/N or Model No.), not Serial (Ser., S/N). Copy every character, including anything after a dash or slash.
Wall ovens
- Open the oven door. Let it cool first.
- Look here first: On the frame around the opening, usually on the left or right side.
- Then check: The top of the frame, under the controls. On a double oven, check the upper oven first.
- Read the line marked Model (Mod., M/N or Model No.), not Serial (Ser., S/N). Copy every character, including anything after a dash or slash.
Can't find the label?
- Check the owner's manual, the receipt, the delivery paperwork or the registration card.
- If it's connected to the brand's app, the model number is in the app's device information.
- Can't read it? Take a photo with the flash off, holding the phone at a slight angle so it doesn't glare, then zoom in.
- Still nothing? Skip it. The guide works without a model number, and our technician will find it at the visit.
| Brand | Model number starts with |
|---|---|
| Amana | AER: electric range · AGR: gas range |
| Bertazzoni | PRO, MAST, HER … GAS: gas range · PRO, MAST, HER … DF: dual-fuel range (electric oven, gas burners) · PRO, MAST, HER … IN: induction range · PRO, MAST, HER … FSE, FDE: wall oven |
| Bosch | HGI, HGS: gas range · HEI, HES: electric range · HII, HIS: induction range · HDI, HDS: dual-fuel range (electric oven, gas burners) · HBL, HBN, HBE: wall oven |
| Café | C2S, C2Y: dual-fuel range (electric oven, gas burners) · CES: electric range · CGS, CGY, CGB: gas range · CHS: induction range · CTS, CTD: wall oven |
| Dacor | HDPR, DOP: dual-fuel range (electric oven, gas burners) · HGPR, DTG: gas range · DTI: induction range · DOB, HWO: wall oven |
| Electrolux | EI … EF, EW … EF: electric range · EI … GF, EW … GF: gas range · EI … IF: induction range · EW … DS: dual-fuel range (electric oven, gas burners) · EI … EW, EW … EW: wall oven |
| Fisher & Paykel | RGV: gas range · RDV: dual-fuel range (electric oven, gas burners) · OR: range · OB: wall oven · OS: steam oven |
| Frigidaire | FFEF, FGEH, FPEH, FCRE: electric range · FFGF, FGGH, FPGH, FCRG: gas range · FGIH, FPIH, GCRI: induction range · FFEW, FGEW, FGET, FCWS: wall oven |
| Gaggenau | BO, BS, BX: wall oven |
| GE | JB, JS, JD: electric range · JGB, JGS: gas range · PB, PS: electric range · PGB, PGS: gas range · PHS: induction range · JT, JK, PT, PK: wall oven |
| GE Monogram | ZGP: gas range · ZDP: dual-fuel range (electric oven, gas burners) · ZTS, ZTD, ZET: wall oven |
| Hotpoint | RB: electric range · RGB: gas range |
| JennAir | JDRP, JDSP: dual-fuel range (electric oven, gas burners) · JGRP, JGSP: gas range · JES: electric range · JGS: gas range · JIS: induction range · JJW, JMW: wall oven |
| KitchenAid | KFE, KSE: electric range · KFG, KSG: gas range · KFD, KSD: dual-fuel range (electric oven, gas burners) · KOS, KOD, KOC: wall oven |
| LG | LDE: electric double-oven range · LDG: gas double-oven range · LRE, LSE: electric range · LRG, LSG: gas range · LSI: induction range · LWS, LWD, LWC: wall oven |
| Maytag | MER: electric range · MGR: gas range · MEW: wall oven |
| Miele | H: wall oven · DG, DGC: steam oven · HR … G: gas range · HR … DF: dual-fuel range (electric oven, gas burners) · HR … I: induction range · HR: range |
| Samsung | NX: gas range · NE: electric range · NY: dual-fuel range (electric oven, gas burners) · NV: wall oven |
| Thermador | PRG: gas pro range · PRD: dual-fuel pro range (electric oven, gas burners) · PRI: induction pro range · ME, MED, PO, POD: wall oven |
| Viking | VGR, RVGR, TVGR: gas range · VDR, RVDR, TVDR: dual-fuel range (electric oven, gas burners) · VER, RVER: electric range · VSOE, VDOE, VSOF: wall oven |
| Whirlpool | WFE, WEE, WFC: electric range · WFG, WEG: gas range · WOS, WOD, WOC: wall oven |
| Wolf | DF: dual-fuel range (electric oven, gas burners) · GR: gas range · IR: induction range · SO, DO, CSO, SPO: wall oven |
Brand notes
- GE, GE Monogram, Café and Hotpoint. GE, Profile, Café and Monogram ovens show F-codes: F3 and F4 usually mean the temperature sensor, F9 the door lock circuit. GE oven F-codes explained
- Thermador. Thermador induction zones need magnetic, flat-bottomed pans that cover most of the zone. Thermador induction not detecting the pan
- Wolf and Viking. Constant clicking on a Wolf or Viking rangetop usually means moisture in a burner or a failing spark switch or module. Wolf and Viking range clicking
- Kenmore. Kenmore appliances are built by other makers, and the three digits before the dot in the model number say which: 110 is Whirlpool laundry, 795 LG refrigerators, 253 Frigidaire refrigerators and freezers. Error codes follow that maker. Kenmore appliance repair
More help with your oven
Questions people ask
Why does my gas oven take so long to light?
A gas oven's igniter has to get hot enough to open the gas valve, and a weak igniter takes longer every year until the oven won't light at all. If the igniter glows but the burner takes more than about 90 seconds to light, or the oven bakes cold, the igniter is usually the fix.
How much does oven repair cost in Los Angeles?
Most oven repairs we do in Los Angeles, Orange and Ventura counties run $160–$720 for parts and labor, for example bake or broil igniter $170–$320 and bake or broil element $180–$340. The diagnostic is $69, applied to the repair, and you get a written quote before any work starts.
Is it worth repairing my oven?
Usually, while the repair costs less than half the price of a comparable new oven and it has life left. Most ovens last 13–15 years, and premium brands 15–20. Past that age, or when the quote passes half the new price, replacing it is usually the better buy, and we'll tell you so.
Checked everything? Call before noon for a same-day visit.
Dispatch answers the phone and the technician arrives with the likely parts. $69 diagnostic, applied to the repair. Written quote before any work.