Garbage disposal troubleshooting guide
A humming garbage disposal is almost always jammed, and a silent one has usually tripped its reset button. Pick what yours is doing for safe checks, with the power off and never a hand in the drain, and when a leak from the bottom means it's time for a new unit.
Last updated
Troubleshoot your garbage disposal
Add the brand and model number for brand notes and error codes, then pick what it's doing. Nothing you type leaves this page.
Brand-specific steps and error codes, if we know the series.
Can't find the label?
- Check the owner's manual, the receipt, the delivery paperwork or the registration card.
- If it's connected to the brand's app, the model number is in the app's device information.
- Can't read it? Take a photo with the flash off, holding the phone at a slight angle so it doesn't glare, then zoom in.
- Still nothing? Skip it. The guide works without a model number, and our technician will find it at the visit.
Garbage disposal humming but not working
A garbage disposal that hums but won't spin is jammed. With the power off, turn the flywheel free with the hex key in the bottom of the unit, remove what jammed it, press the reset button and try again.
Most likely, in the order we find it: A jammed flywheel or a seized motor.
-
Turn it off and cut the power
Switch off the disposal, then switch off its breaker or unplug it under the sink.
-
Free it with the hex key
Put a 1/4-inch hex key (Allen wrench; many disposals come with one) into the socket in the center of the bottom of the unit and work it back and forth until it turns a full circle.
You'll need: 1/4-inch hex key
-
Remove what jammed it
Use tongs or pliers to take out the object, never your hand.
-
Press the reset button
Press the red button on the bottom of the unit until it clicks.
-
Test it
Restore the power, run cold water and switch it on.
Still humming: the motor or a deeper jam. Call.
Still not working?
- What we check
- Manual rotation, reset, motor condition
- Typical repair
- Jam clearing and reset $69 diagnostic covers itParts and labor, typical for LA, OC & Ventura; written quote before any work.
- The visit
- $69 diagnostic, applied to the repair · Usually same-day
Read: Garbage Disposal Humming but Not Working? 5-Step ResetGo through these steps one at a time
Garbage disposal leaking
Where a garbage disposal leaks decides the fix: at the sink flange or the hose connections it's usually repairable; from the bottom of the unit, the internal seal has failed and the disposal needs replacing.
Most likely, in the order we find it: Sink flange, the dishwasher inlet, or the body seal.
-
Find the leak
Dry everything, add a few drops of food coloring to water in the sink and watch where the color appears.
-
Tighten what you can
Hand-tighten the drain pipe and the dishwasher hose connections.
-
Bottom leak? Replace it
Water from the bottom of the unit means the internal seal has failed.
We can replace the disposal on the visit.
Still not working?
- What we check
- Where it drips during fill and run
- Typical repair
- Flange / connection reseal $140–$220 · Replacement unit installed (1/2–3/4 HP) $320–$560Parts and labor, typical for LA, OC & Ventura; written quote before any work.
- The visit
- $69 diagnostic, applied to the repair · Usually same-day
Read: Garbage Disposal Leaking from the Bottom: Fix or Replace?Go through these steps one at a time
Garbage disposal dead, no sound
A garbage disposal that makes no sound has usually tripped its reset button, its breaker or GFCI, or lost power at the wall switch or the plug under the sink.
Most likely, in the order we find it: Tripped reset button, breaker, switch or motor.
-
Press the reset button
Press the red button on the bottom of the unit until it clicks.
-
Check the power
Check the wall switch, the plug under the sink and the breaker or GFCI outlet.
-
Call
No power with a working outlet means the switch, the wiring or the motor.
Still not working?
- What we check
- Reset, power, switch
- Typical repair
- Replacement unit installed (1/2–3/4 HP) $320–$560Parts and labor, typical for LA, OC & Ventura; written quote before any work.
- The visit
- $69 diagnostic, applied to the repair · Usually same-day
Garbage disposal draining slowly
A garbage disposal that drains slowly is usually fed too much at once or the wrong food: fibrous peels, grease, rice and pasta. A clog below the disposal is a plumbing job.
Most likely, in the order we find it: A clog in the trap or drain line, or worn grinding parts.
-
Run cold water longer
Run cold water before, during and for 15 seconds after grinding.
-
Feed it slowly
Small amounts at a time, and no grease, celery, potato peels, rice or pasta.
-
Call the right trade
We fix the disposal; a clog in the drain pipe beyond it is a plumber's job.
Still not working?
- What we check
- Grinding chamber and trap — a clog past the trap is a plumber's job, and we'll say so
- Typical repair
- Quoted in writing after the diagnostic.
- The visit
- $69 diagnostic, applied to the repair · Usually same-day
Garbage disposal error codes by brand
Most garbage disposals show few codes. If yours shows one, write it down exactly, switch the breaker off for 1 minute and back on, and if it returns, call with the code and the model number.
Where's the model number on a garbage disposal?
It's on a sticker called the rating label, and you can reach it without tools. The model number tells the tool above (and our technician) which series you have; the serial number on the same label holds the build date. Watch 0 and O, 1 and I, 8 and B.
- Open the cabinet under the sink. Use a flashlight.
- Look here first: On the side of the disposal.
- Then check: On the bottom of the unit: hold your phone underneath and take a photo instead of crawling in. The box or the receipt has it too.
- Read the line marked Model (Mod., M/N or Model No.), not Serial (Ser., S/N). Copy every character, including anything after a dash or slash.
Never put your hand inside the disposal, even when it's off.
Can't find the label?
- Check the owner's manual, the receipt, the delivery paperwork or the registration card.
- If it's connected to the brand's app, the model number is in the app's device information.
- Can't read it? Take a photo with the flash off, holding the phone at a slight angle so it doesn't glare, then zoom in.
- Still nothing? Skip it. The guide works without a model number, and our technician will find it at the visit.
| Brand | Model number starts with |
|---|---|
| GE | GFC: garbage disposal |
Brand notes
- Kenmore. Kenmore appliances are built by other makers, and the three digits before the dot in the model number say which: 110 is Whirlpool laundry, 795 LG refrigerators, 253 Frigidaire refrigerators and freezers. Error codes follow that maker. Kenmore appliance repair
More help with your garbage disposal
Questions people ask
Should I repair or replace a leaking garbage disposal?
It depends on where it leaks. Leaks at the sink flange or the hose connections are usually fixable. A leak from the bottom of the unit means the internal seal has failed and water is reaching the motor, so replacing the disposal is the right call.
How much does garbage disposal repair cost in Los Angeles?
Most garbage disposal repairs we do in Los Angeles, Orange and Ventura counties run $140–$780 for parts and labor, for example flange / connection reseal $140–$220 and replacement unit installed (1/2–3/4 HP) $320–$560. The diagnostic is $69, applied to the repair, and you get a written quote before any work starts.
Is it worth repairing my garbage disposal?
Usually, while the repair costs less than half the price of a comparable new garbage disposal and it has life left. Most garbage disposals last 10–12 years, and premium brands 10–12. Past that age, or when the quote passes half the new price, replacing it is usually the better buy, and we'll tell you so.
Checked everything? Call before noon for a same-day visit.
Dispatch answers the phone and the technician arrives with the likely parts. $69 diagnostic, applied to the repair. Written quote before any work.