Dishwasher troubleshooting guide
Most dishwasher problems start at the filter, the drain hose or the garbage disposal it drains through. Pick what yours is doing for safe checks in the order our technicians find the cause, what each brand's error code means and when to stop and call.
Last updated
Troubleshoot your dishwasher
Add the brand and model number for brand notes and error codes, then pick what it's doing. Nothing you type leaves this page.
Brand-specific steps and error codes, if we know the series.
Can't find the label?
- Check the owner's manual, the receipt, the delivery paperwork or the registration card.
- If it's connected to the brand's app, the model number is in the app's device information.
- Can't read it? Take a photo with the flash off, holding the phone at a slight angle so it doesn't glare, then zoom in.
- Still nothing? Skip it. The guide works without a model number, and our technician will find it at the visit.
Dishwasher not draining
A dishwasher that won't drain usually has a clogged filter, a kinked drain hose, a blocked garbage disposal or air gap, or a drain pump jammed by glass or a pit. The first three take about ten minutes to check.
Most likely, in the order we find it: Drain pump, clogged filter or sump, check valve, or the air gap or drain hose.
-
Clean the filter
Take out the bottom rack, twist out the filter at the bottom of the tub (usually counterclockwise), rinse it under the tap with a soft brush and twist it back in until it locks.
Standing water drains on the next cycle if this was it.
-
Run the garbage disposal
If the dishwasher drains through the disposal, run the disposal with cold water for 30 seconds. A newly installed disposal needs the knockout plug in its dishwasher inlet removed.
Clogs in the disposal back up into the dishwasher.
-
Clear the air gap
If there's a small chrome cap on the sink deck, pull it off and clear the food or gunk inside.
Water spraying from the air gap while the dishwasher drains means it's clogged.
-
Check the drain hose
Under the sink, make sure the drain hose isn't kinked and loops up high before it connects to the drain or the disposal.
-
Cancel to drain
Cancel the cycle (on many models, hold Start or Cancel for 3 seconds) so it pumps out.
A hum with no water moving, or no sound at all, points to the drain pump.
Still not working?
- What we check
- Filter, pump impeller, drain path, air gap
- Typical repair
- Drain pump $190–$330Parts and labor, typical for LA, OC & Ventura; written quote before any work.
- The visit
- $69 diagnostic, applied to the repair · Usually fixed on the first visit
Read: Dishwasher Not Draining? 7 Causes, Checks and LA PricesGo through these steps one at a time
Dishwasher not cleaning well
Dishes that come out gritty or spotted usually mean a dirty filter, blocked spray arms, water that isn't hot enough, or a detergent or rinse-aid problem. Hard water in Los Angeles makes spots and film worse.
Most likely, in the order we find it: Wash pump, spray arms, inlet valve or water temperature.
-
Clean the filter
Take out the bottom rack, twist out the filter at the bottom of the tub (usually counterclockwise), rinse it under the tap with a soft brush and twist it back in until it locks.
-
Clear the spray arms
Spin each arm by hand; it should turn freely. Rinse out the holes and clear blocked ones with a toothpick.
-
Run the tap hot first
Run the kitchen faucet until the water is hot before you start, so the first fill isn't cold.
-
Check the detergent and rinse aid
Use fresh detergent (old powder clumps) and keep the rinse aid filled; it's what fights hard-water spots.
-
Load for the spray
Nothing tall should block the spray arms or the detergent door, and dirty surfaces should face the center.
Still gritty after all that: the wash pump, heater or inlet valve may be weak. Call.
Still not working?
- What we check
- Spray-arm flow, fill level, heater and circulation
- Typical repair
- Wash pump / circulation motor $280–$520 · Inlet valve or float switch $170–$300Parts and labor, typical for LA, OC & Ventura; written quote before any work.
- The visit
- $69 diagnostic, applied to the repair · Usually same-day
Dishwasher leaking
A leaking dishwasher usually has suds from the wrong detergent, a dirty or torn door seal, a tub that tilts forward, or a loose connection under the sink. Water under the dishwasher, or a leak code, means turn off the water first.
Most likely, in the order we find it: Door gasket, float switch, pump seal or a hose.
-
Shut off the water and power if it's on the floor
If water is pooling under the dishwasher or a leak code shows, close the valve under the sink and switch off the dishwasher's breaker.
-
Use dishwasher detergent only
Hand dish soap makes suds that push water out of the door. If that happened, run a rinse with no detergent.
-
Clean and check the door seal
Wipe the rubber seal around the door and look for tears or food stuck in it.
-
Check that it's level
A dishwasher that tilts toward you leaks at the door. Check with a level across the open door or the tub edge.
Leveling is done at the feet; your manual shows how.
-
Look under the sink
With a flashlight, watch the supply and drain connections under the sink while the dishwasher fills.
A drip at a connection is a quick fix; a cracked hose needs replacing.
You'll need: Flashlight
Still not working?
- What we check
- Door seal, float, fill level, hoses
- Typical repair
- Inlet valve or float switch $170–$300Parts and labor, typical for LA, OC & Ventura; written quote before any work.
- The visit
- $69 diagnostic, applied to the repair · Usually same-day
Dishwasher won't start
A dishwasher that won't start usually has a door that isn't latched, the control lock on, a delay start set, or no power because a wall switch or breaker is off. If it has power and the door latches, the latch or the control is the likely fix.
Most likely, in the order we find it: Door latch, control board, user interface or thermal fuse.
-
Latch the door
Close the door firmly until it clicks. A rack or a tall dish sticking out stops it latching.
-
Turn off the lock and the delay
A lock icon means Control Lock is on: hold the lock button (usually marked) for 3 seconds. Cancel any Delay Start.
-
Check the power
Many dishwashers run off a wall switch near the sink (sometimes shared with the disposal) and have their own breaker. Check both.
-
Reset it
Switch it off at the breaker (or unplug it) for 1 full minute, then switch it back on. Then try a short cycle.
Still dead with the door latched: the latch switch, the control or a thermal fuse needs testing.
Still not working?
- What we check
- Latch, board, fuse, power
- Typical repair
- Door latch / switch $160–$290 · Control board $260–$560Parts and labor, typical for LA, OC & Ventura; written quote before any work.
- The visit
- $69 diagnostic, applied to the repair · Usually same-day
Read: Dishwasher Won't Start? Causes, Checks and Reset StepsGo through these steps one at a time
Dishwasher not drying
Wet dishes usually come down to an empty rinse-aid dispenser or an energy-saving dry setting, and plastic always dries worse than glass. If nothing dries even with rinse aid and heated dry on, the heater or the drying fan has failed.
Most likely, in the order we find it: Heating element, vent, or the rinse-aid dispenser.
-
Fill the rinse aid
Rinse aid helps water sheet off. Without it, dishes stay wet and spotted.
-
Turn on heated or extra dry
Many quiet, efficient models dry by condensation unless you choose Heated Dry, Extra Dry or Sanitize.
-
Unload the bottom rack first
That way water pooled on the top-rack cups doesn't spill onto dry dishes.
-
Let the steam out
Open the door a few inches when the cycle ends (some models do this on their own).
If nothing dries even with rinse aid and heated dry, call: the heater or the drying fan is the likely fix.
Still not working?
- What we check
- Element continuity, vent fan, dispenser
- Typical repair
- Heating element $220–$380Parts and labor, typical for LA, OC & Ventura; written quote before any work.
- The visit
- $69 diagnostic, applied to the repair · Usually same-day
Read: Dishwasher Not Drying Dishes? Causes and FixesGo through these steps one at a time
Dishwasher grinding or loud
A loud dishwasher is often a spray arm hitting a dish or something hard caught in the pump. Grinding during the wash points to the wash pump; grinding while it drains points to the drain pump.
Most likely, in the order we find it: Debris in the pump or chopper, or a failing wash or drain pump motor.
-
Check the spray arms' path
Spin each arm by hand with the racks loaded. A pan handle or a utensil can catch it and thump.
-
Look in the sump
Take out the filter and look in the opening underneath for glass, a pit or a bone. Wear gloves and pick it out carefully.
You'll need: Gloves, flashlight
-
Note when it's loud
A hum during the drain and water swishing are normal. Grinding during the wash points to the wash pump, and during the drain to the drain pump.
Call if the grinding continues after clearing debris.
Still not working?
- What we check
- Filter and sump debris, pump impellers
- Typical repair
- Drain pump $190–$330 · Wash pump / circulation motor $280–$520Parts and labor, typical for LA, OC & Ventura; written quote before any work.
- The visit
- $69 diagnostic, applied to the repair · Usually same-day
Read: Dishwasher Grinding Noise: Causes, Checks and CostsGo through these steps one at a time
Dishwasher error codes: what to do first
A dishwasher error code usually points to the water supply, the drain, a leak, the heater or the control. Leak codes come first: turn off the water and power. For the rest, fix the obvious cause, reset once and call if the code returns.
Most likely, in the order we find it: Drain, leak, heater or fill faults, depending on the code.
-
Leak code? Water and power off
If the code means a leak or water in the base, close the valve under the sink and switch off the breaker before anything else.
-
Write the code down
Note every character, and whether lights flash in a pattern. Some models without a display count codes out in blinks.
Type it into the tool above with your brand, or find it in the tables below.
-
Fix the obvious cause
Drain codes: the filter, drain hose, disposal and air gap. Fill codes: the valve under the sink and the supply line.
-
Reset once
Switch it off at the breaker (or unplug it) for 1 full minute, then switch it back on. Then run a short cycle.
If the code returns, call with the code and the model number.
Still not working?
- What we check
- Read stored codes and test the flagged system
- Typical repair
- Drain pump $190–$330 · Control board $260–$560Parts and labor, typical for LA, OC & Ventura; written quote before any work.
- The visit
- $69 diagnostic, applied to the repair · Usually same-day
Read: Bosch Dishwasher E24, E25 and E15: Meaning and FixesGo through these steps one at a time
Dishwasher error codes by brand
What the code on the display means and what to try first. Codes vary by model and year: if your owner's manual says something different, it wins. If the code comes back after one reset, call with the code and the model number.
Samsung dishwasher error codes
| Code | What it means | What to try first |
|---|---|---|
| 4C, 4E | Water supply problem | Open the valve under the sink fully and check the supply line for kinks. |
| 5C, SC, 5E, SE | Not draining | Clean the filter, check the drain hose and run the disposal. Steps: dishwasher not draining |
| LC, LE | Leak detected | Close the valve under the sink, switch off the breaker and call. Steps: dishwasher leaking |
| 1E, IE | Filter clogged (Waterwall models) | Clean the filter. Steps: dishwasher not cleaning well |
| HE | Heater or temperature reading problem | Empty it, add detergent and run a normal cycle; call if it returns. Steps: dishwasher not drying |
| 3E | Incoming water too hot (over 176°F) | Check the water heater setting; if it returns, switch off the breaker and call. |
| 3C | Wash pump problem | Check the hot water isn't over 176°F; call if it returns. |
| 7E | Waterwall bar can't move | Make sure nothing blocks the bar at the back of the tub, then restart. Steps: dishwasher not cleaning well |
| PC, PE | Zone Wash or half-load feature problem | Restart; then empty it, add detergent and run a normal cycle. |
| AP | Wi-Fi setup mode, not a fault | Finish or cancel the SmartThings setup. |
LG dishwasher error codes
| Code | What it means | What to try first |
|---|---|---|
| OE | Not draining | Clean the filter, straighten the drain hose and clear the air gap or disposal (a new disposal needs its knockout plug removed). Steps: dishwasher not draining |
| IE | Not filling: not enough water reached the tub | Open the valve under the sink and check the supply line for kinks. |
| AE, E1 | Leak detected: water in the base | Close the water valve and switch off the breaker. Hand dish soap and a unit that isn't level can cause it. Steps: dishwasher leaking |
| FE | Too much water supplied | Don't use hand dish soap; the dishwasher keeps draining to protect the floor. Call if it repeats. Steps: dishwasher leaking |
| bE | Too many suds from the wrong detergent | Use dishwasher detergent only and run a rinse with no detergent. Steps: dishwasher leaking |
| HE | Heater fault: the water isn't heating | Call. Steps: dishwasher not drying |
| tE | Temperature sensor fault | Call. |
| LE | Wash motor fault | Reset the power once; call if it returns. Steps: dishwasher grinding or loud |
| CL | Child lock on, not an error | Hold the Child Lock button (or the marked pair) for 3 seconds. Steps: dishwasher won't start |
| PF | The power was interrupted | Restart the cycle. |
| 2H | Two hours left in the cycle, not an error | Nothing to fix. |
Source: LG USA: dishwasher guide to error codes; LG USA: error codes, dishwasher
Whirlpool and Maytag dishwasher error codes
Also KitchenAid, JennAir and Amana, which use the same F#E# codes: F is the system, E the fault.
| Code | What it means | What to try first |
|---|---|---|
| F9 E1 | Long drain: not draining | Clean the filter, unkink the drain hose and check the disposal and its knockout plug. Steps: dishwasher not draining |
| F8 E4 | Water in the drip tray under the tub | Turn off the power and water and look for leaks at the supply and drain connections. Steps: dishwasher leaking |
| H2O | Not detecting water | Open the supply valve under the sink fully and check the line for kinks. |
| F7 E2 | Wash motor error | Cut the power for 30 seconds; call if it returns. Steps: dishwasher grinding or loud |
| F6 E1 | Control or keypad error | Cut the power for 30 seconds; call if it returns. Steps: dishwasher won't start |
Source: Whirlpool: dishwasher error codes, reading · More detail: Whirlpool Error Codes: Washer, Dryer, Dishwasher, Fridge
Bosch dishwasher error codes
Thermador and Gaggenau dishwashers are made by the same company and generally use the same codes; check your manual.
| Code | What it means | What to try first |
|---|---|---|
| E24, E6103 | Not draining properly | Clean the filter and check the drain hose, the air gap and the disposal knockout plug. Steps: dishwasher not draining |
| E25, E6102 | Drain pump blocked, or its cover loose or missing | Clear the pump cover under the filter. Steps: dishwasher not draining |
| E22, E9240 | Filter blocked | Wash the filter. Steps: dishwasher not cleaning well |
| E23, E6101 | Drain pump blocked, clogged or faulty | Check the pump cover for debris; call if it returns. Steps: dishwasher not draining |
| E15, E3100 | Water in the base: leak protection activated | Shut off the water, look for visible leaks and call. Steps: dishwasher leaking |
Source: Bosch US: dishwasher error codes · More detail: Bosch Dishwasher E24, E25 and E15: Meaning and Fixes
Frigidaire and Electrolux dishwasher error codes
| Code | What it means | What to try first |
|---|---|---|
| i10 | Low fill: not enough water | Open the valve under the sink fully and check the supply line for kinks. |
| i20, i40, iF0 | Drain restricted or water-level problem | Clean the filter and check the drain hose, the disposal and the air gap. Steps: dishwasher not draining |
| i30 | Water in the base (leak) | Turn off the water and the power, then call. Steps: dishwasher leaking |
| i60 | Heating problem | Call. Steps: dishwasher not drying |
Source: Frigidaire FGID2466QF owner's guide, error codes (manual copy); Electrolux support: dishwasher displays an error code
Miele dishwasher error codes
| Code | What it means | What to try first |
|---|---|---|
| F11 | Drain fault: water left in the wash cabinet | Clean the filter combination and check the drain pump cover and the drain hose. Steps: dishwasher not draining |
| F13, F12, F15 | Water inlet blocked or restricted | Make sure the water valve is open, clean the inlet filter and straighten the hose. |
| F70 | The Waterproof system has reacted (leak) | Shut off the water, switch the dishwasher off and unplug it, then call. Steps: dishwasher leaking |
Source: Miele USA: fault F11; Miele USA: fault F13, water inlet; Miele USA: fault F70, Waterproof system · More detail: Miele Dishwasher F11 and F13 Faults: What to Do
Where's the model number on a dishwasher?
It's on a sticker called the rating label, and you can reach it without tools. The model number tells the tool above (and our technician) which series you have; the serial number on the same label holds the build date. Watch 0 and O, 1 and I, 8 and B.
- Open the door all the way down.
- Look here first: Along the edge of the door: the right or left side, sometimes the top.
- Then check: The tub frame, on either side of the opening.
- Read the line marked Model (Mod., M/N or Model No.), not Serial (Ser., S/N). Copy every character, including anything after a dash or slash.
Can't find the label?
- Check the owner's manual, the receipt, the delivery paperwork or the registration card.
- If it's connected to the brand's app, the model number is in the app's device information.
- Can't read it? Take a photo with the flash off, holding the phone at a slight angle so it doesn't glare, then zoom in.
- Still nothing? Skip it. The guide works without a model number, and our technician will find it at the visit.
| Brand | Model number starts with |
|---|---|
| Amana | ADB: dishwasher |
| Bosch | SHE, SHX, SHP, SHV, SPE, SPX: dishwasher |
| Café | CDT: dishwasher |
| Cove | DW: dishwasher |
| Dacor | DDW: dishwasher |
| Electrolux | EI … ID, EW … ID: dishwasher |
| Fisher & Paykel | DD: DishDrawer dishwasher · DW: dishwasher |
| Frigidaire | FFCD, FFID, FGID, FPID, FDPC: dishwasher |
| Gaggenau | DF: dishwasher |
| GE | GDT, GDF, GDP, PDT: dishwasher |
| GE Monogram | ZDT: dishwasher |
| Hotpoint | HDA: dishwasher |
| JennAir | JDB, JDT: dishwasher |
| KitchenAid | KDT, KDP, KDF: dishwasher |
| LG | LDF, LDT, LDP, LDS: dishwasher |
| Maytag | MDB: dishwasher |
| Miele | G: dishwasher |
| Samsung | DW: dishwasher |
| Thermador | DWHD: dishwasher |
| Viking | VDWU, FDWU, RVDW: dishwasher |
| Whirlpool | WDT, WDF, WDP: dishwasher |
Brand notes
- Whirlpool, Maytag, KitchenAid, JennAir, Amana and Roper. Whirlpool, Maytag, KitchenAid, JennAir and Amana use the same F#E# codes: F is the system and E the fault. Whirlpool error codes explained
- Bosch, Bosch Benchmark, Thermador and Gaggenau. E24 and E25 mean water isn't draining; E15 means water reached the base and the leak protection tripped, so turn off the water first. Bosch dishwasher E24 and E15
- Miele. Miele F11 is a drain fault and F13 a water inlet fault; F70 means the Waterproof system reacted to a leak. Miele dishwasher F11 and F13
- Fisher & Paykel. DishDrawers drain through a filter and pump in each drawer, so one drawer can drain while the other doesn't. Fisher & Paykel DishDrawer not draining
- Kenmore. Kenmore appliances are built by other makers, and the three digits before the dot in the model number say which: 110 is Whirlpool laundry, 795 LG refrigerators, 253 Frigidaire refrigerators and freezers. Error codes follow that maker. Kenmore appliance repair
More help with your dishwasher
- Dishwasher repair in Los Angeles, Orange and Ventura counties
- Dishwasher Grinding Noise: Causes, Checks and Costs
- Dishwasher Not Draining? 7 Causes, Checks and LA Prices
- Dishwasher Not Drying Dishes? Causes and Fixes
- Dishwasher Won't Start? Causes, Checks and Reset Steps
- Bosch Dishwasher E24, E25 and E15: Meaning and Fixes
- Fisher & Paykel DishDrawer Not Draining? What to Check
- Miele Dishwasher F11 and F13 Faults: What to Do
Questions people ask
Why is there water in the bottom of my dishwasher?
A little water around the filter after a cycle is normal on many models. An inch or more means it isn't draining: clean the filter, check the drain hose for kinks, run the garbage disposal and clear the sink air gap if you have one. If it still won't drain, the drain pump is the usual fix.
How much does dishwasher repair cost in Los Angeles?
Most dishwasher repairs we do in Los Angeles, Orange and Ventura counties run $160–$560 for parts and labor, for example drain pump $190–$330 and door latch / switch $160–$290. The diagnostic is $69, applied to the repair, and you get a written quote before any work starts.
Is it worth repairing my dishwasher?
Usually, while the repair costs less than half the price of a comparable new dishwasher and it has life left. Most dishwashers last 10–12 years, and premium brands 12–15. Past that age, or when the quote passes half the new price, replacing it is usually the better buy, and we'll tell you so.
Checked everything? Call before noon for a same-day visit.
Dispatch answers the phone and the technician arrives with the likely parts. $69 diagnostic, applied to the repair. Written quote before any work.