Refrigerator troubleshooting guide

Most refrigerator problems trace back to dusty condenser coils, blocked vents, a door that doesn't seal or a defrost system that has stopped working. Pick what yours is doing for safe checks in the order our technicians find the cause, what each error code means and when to stop and call.

Last updated

Troubleshoot your refrigerator

Add the brand and model number for brand notes and error codes, then pick what it's doing. Nothing you type leaves this page.

Appliance Refrigerator

Brand-specific steps and error codes, if we know the series.

What's the refrigerator doing?

Refrigerator not cooling

A refrigerator that isn't cooling usually has dusty condenser coils, blocked vents, a door that isn't sealing, or a fan or start part that has failed. Rule out the settings and showroom mode first; you can check the rest in about half an hour.

Most likely, in the order we find it: Condenser fan, evaporator fan, start relay, control board, or a sealed-system fault.

  1. Check the settings and showroom mode

    Set the fresh-food section to 37–38°F and the freezer to 0°F. If the display shows OFF, OF OF or a demo message, the refrigerator is in showroom mode: the lights work but nothing cools.

    Showroom mode switches off with a button combination from your manual (see the brand notes). No repair needed.

  2. Listen for it running

    Close the doors for 10 minutes, then listen at the bottom back. A running refrigerator hums, blows warm air from the bottom grille, and you can hear a fan inside the freezer.

    Silent with the light on, or a click every few minutes that never turns into a hum, points to the compressor or its start relay. Skip to calling.

  3. Clean the condenser coils

    Unplug the refrigerator. Snap off the grille at the bottom front (or roll the refrigerator out if the coils are on the back) and vacuum the coils and the fan area with a brush attachment.

    Coils packed with dust can't release heat. Cooling should improve within a day of cleaning.

    You'll need: Vacuum with a brush attachment, flashlight

  4. Clear the vents inside

    Move food away from the air vents on the back wall of the freezer and the fresh-food section, and don't overfill either one.

    Cold air has to travel from the freezer to the fridge section, and blocked vents stop it.

  5. Test the door seals

    Close the door on a dollar bill at several spots around the seal and pull it out. It should drag. Where it slides out freely, the seal isn't sealing. Clean the seals with warm soapy water and make sure no shelf or bin holds a door open.

    A leaking seal lets warm air in faster than the refrigerator can remove it.

  6. Check the temperature after 24 hours

    Put a thermometer in a glass of water on the middle shelf, keep the doors closed and read it the next day.

    40°F or below: fixed. Above 40°F: it needs a repair. Food stays safe about 4 hours in a closed refrigerator, so move perishables to a cooler with ice.

Still not working?

What we check
Compressor start, fan operation, coil temperature, defrost cycle and control signals
Typical repair
Start relay / capacitor $160–$280 · Evaporator or condenser fan motor $190–$340 · Compressor or sealed-system repair $650–$1,400Parts and labor, typical for LA, OC & Ventura; written quote before any work.
The visit
$85 diagnostic, applied to the repair · Usually same-day; sealed-system work is scheduled

Fridge section warm, freezer cold

When the freezer stays cold but the fridge section warms up, cold air isn't getting from the freezer to the fridge: blocked vents, a freezer fan that has stopped, or frost from a failed defrost system blocking the airflow.

Most likely, in the order we find it: Evaporator fan, air damper, defrost heater or thermostat (frost build-up blocks the airflow).

  1. Clear the vents between the sections

    Move food away from the vents in the freezer and on the back wall of the fridge section, especially near the top.

    If cold air flows from the fridge vents again, the temperature recovers within a day.

  2. Listen for the freezer fan

    Open the freezer and press the door switch in the frame with a finger (it tells the refrigerator the door is closed). You should hear the fan inside start.

    No fan sound, or ticking or scraping, means the fan has failed or ice is touching it.

  3. Look for frost on the back wall

    Check the back wall inside the freezer, and inside the fridge section on models with two cooling systems. A thin, even layer is normal; thick white frost or a sheet of ice is not.

    Heavy frost means the defrost system has stopped. A technician tests the defrost heater, sensor and control.

  4. Defrost it to buy time

    If you found heavy frost: move the food to coolers, unplug the refrigerator, prop the doors open with towels down and wait 24 hours before plugging it back in.

    It should cool normally for a while. If the fridge section warms up again within a few weeks, the defrost system needs repairing.

Still not working?

What we check
Frost pattern on the evaporator, damper movement, fan voltage
Typical repair
Evaporator or condenser fan motor $190–$340 · Defrost heater, thermostat or sensor $190–$360Parts and labor, typical for LA, OC & Ventura; written quote before any work.
The visit
$85 diagnostic, applied to the repair · Usually fixed on the first visit

Refrigerator leaking water

A refrigerator leaking water usually has a clogged defrost drain, a loose or cracked water line, or a water filter that isn't seated. Where the water appears tells you which, so start by finding where it begins.

Most likely, in the order we find it: Blocked defrost drain, cracked drain pan, water-line or inlet-valve leak.

  1. Keep water away from the outlet

    If water has reached the outlet or the cord, switch off the refrigerator's breaker before you touch the plug.

  2. Find where the water starts

    Dry the floor, lay paper towels along the front and sides, and check after an hour or two.

    Water at the front center usually comes from inside (the defrost drain). Water at the back points to the water line or the drain pan underneath.

  3. Look under the crisper drawers

    Take out the crisper drawers and look under them and on the floor of the fresh-food section.

    Water or ice there means the defrost drain is blocked. On many models you can flush the drain hole at the bottom of the back wall with warm water and a turkey baster; if it's behind a panel, call.

  4. Reseat the water filter

    If the filter was changed recently, take it out and push it back in until it locks. Use the filter your refrigerator's brand specifies.

    Drips at the filter head stop once it seats. Off-brand filters can fit loosely.

  5. Check the water line at the back

    Close the valve that feeds the refrigerator (under the sink or behind the refrigerator), roll it out gently and look at the connection on the back with a flashlight.

    A wet fitting or a cracked plastic line needs replacing. Keep the valve closed and call.

    You'll need: Flashlight

Still not working?

What we check
Drain path, inlet valve, ice-maker line and door gaskets
Typical repair
Water inlet valve / ice-maker assembly $210–$420Parts and labor, typical for LA, OC & Ventura; written quote before any work.
The visit
$85 diagnostic, applied to the repair · Usually fixed on the first visit

Refrigerator buzzing, humming or clicking

Most refrigerator sounds are normal: hums, gurgles and the click of the defrost cycle. A loud buzz, rattle or squeal usually comes from a fan, the ice maker's water valve or something touching the condenser fan underneath.

Most likely, in the order we find it: Condenser or evaporator fan motor, the start relay (clicking), compressor mounts, ice-maker fill valve.

  1. Find where it comes from

    Listen at the bottom back, inside the freezer and near the ice maker. Then open the freezer door: the fan inside usually stops.

    Noise that stops when the freezer opens is the freezer fan or ice touching it. Noise from the bottom back is the condenser fan or the compressor.

  2. Check the ice maker's water

    A buzz every few minutes can be the ice maker trying to fill with the water shut off. Open the supply valve, or switch the ice maker off if it isn't connected.

    If the buzzing stops, that was it.

  3. Clean and clear underneath

    Unplug the refrigerator. Snap off the grille at the bottom front (or roll the refrigerator out if the coils are on the back) and vacuum the coils and the fan area with a brush attachment. Make sure no paper, toy or cord touches the fan.

    A rattle or ticking from the bottom often stops right away.

  4. Make sure it isn't touching anything

    Move the refrigerator so it doesn't touch cabinets or the wall, and take loose items off the top.

    Vibration through cabinets sounds much louder than it is.

  5. Watch for click-and-warm

    Listen for a click, a minute of quiet, then another click a few minutes later while the refrigerator gets warmer.

    That pattern means the compressor isn't starting (a start relay or compressor fault). Call before the food warms up.

Still not working?

What we check
Which fan is noisy, compressor start, ice-maker cycle
Typical repair
Start relay / capacitor $160–$280 · Evaporator or condenser fan motor $190–$340Parts and labor, typical for LA, OC & Ventura; written quote before any work.
The visit
$85 diagnostic, applied to the repair · Usually same-day

No ice or water from the dispenser

No ice or water usually means water isn't reaching the refrigerator: a closed valve, a clogged filter or a kinked line. A freezer warmer than about 10°F also stops ice. Check those before suspecting the ice maker itself.

Most likely, in the order we find it: Inlet valve, frozen fill tube, ice-maker module, water filter or low water pressure.

  1. Make sure the ice maker is on

    Check the ice maker switch, the wire arm (it must be down) or the Ice Off setting on the display.

    Once it's on, the first ice takes about 24 hours.

  2. Set the freezer to 0°F

    Most ice makers slow down or stop when the freezer is warmer than about 10°F.

    If the freezer can't reach 0°F, follow the not-cooling steps first.

  3. Open the water supply

    Make sure the valve feeding the refrigerator is fully open and the line behind it isn't kinked from being pushed back.

    Water flows again right away if this was it.

  4. Replace the water filter

    A filter older than about six months can slow the water to a trickle. Install a new one, then run water from the dispenser for a few minutes to push the air out.

    A strong, steady stream means the ice maker gets enough water too.

  5. Clear ice jams

    Take out the ice bucket and look for a frozen clump or ice in the chute. Thaw the bucket in the sink, and never chip at the ice maker with a knife.

    If the ice maker itself is buried in ice, as happens on some French-door models, see the brand notes.

  6. Read what still works

    Water but no ice points to the ice maker or its fill tube. Neither ice nor water points to the inlet valve or a frozen water line in the door.

    A technician tests the valve, the fill tube and the ice maker on one visit.

Still not working?

What we check
Water supply, valve coil, module cycle, filter age
Typical repair
Water inlet valve / ice-maker assembly $210–$420Parts and labor, typical for LA, OC & Ventura; written quote before any work.
The visit
$85 diagnostic, applied to the repair · Usually same-day

Refrigerator running constantly or frosting up

A refrigerator that runs nonstop or frosts up is usually losing cold air through a door seal, set too cold, or fighting dirty coils or a hot room. Frost spread evenly over the back wall instead points to a failed defrost system.

Most likely, in the order we find it: Door gasket, defrost system, dirty condenser coils, or a failing thermistor.

  1. Check that the doors close and seal

    Make sure every door and drawer closes on its own, then do the dollar-bill test around each seal. Look for a shelf or bin holding a door open.

    A door left slightly open is the most common cause of frost on food and near the door.

  2. Check the settings

    Set 37–38°F and 0°F, and turn off any fast-cool or fast-freeze mode (Power Cool, Power Freeze, Ice Plus, Express Freeze) left on.

    Those modes run the compressor hard on purpose.

  3. Clean the condenser coils

    Unplug the refrigerator. Snap off the grille at the bottom front (or roll the refrigerator out if the coils are on the back) and vacuum the coils and the fan area with a brush attachment.

    Clean coils let it run in shorter cycles.

    You'll need: Vacuum with a brush attachment

  4. Read the frost pattern

    Frost on food and near the door seal means warm air is getting in. A thick, even coat over the back wall of the freezer means the defrost system has failed.

    A failed defrost system needs a technician: the heater, sensor or control is tested.

  5. Think about the room

    In a garage that tops 100°F in summer, a refrigerator can run almost nonstop just to keep up.

    That isn't a fault, but it wears the compressor faster. A shaded, ventilated spot helps.

Still not working?

What we check
Gasket seal, coil condition, defrost components
Typical repair
Defrost heater, thermostat or sensor $190–$360Parts and labor, typical for LA, OC & Ventura; written quote before any work.
The visit
$85 diagnostic, applied to the repair · Usually same-day

Refrigerator error codes by brand

What the code on the display means and what to try first. Codes vary by model and year: if your owner's manual says something different, it wins. If the code comes back after one reset, call with the code and the model number.

Samsung refrigerator error codes

Samsung refrigerator error codes
CodeWhat it meansWhat to try first
OF OF, O FF, OFF OFFCooling Off (showroom) mode: cooling, ice and water are switched off. Not a faultSwitch it off with your model's button combination (Samsung's guide is linked below). Steps: refrigerator not cooling
22E, 22CFridge fan error, often after a door was left openUnplug it for a few hours with the doors open to defrost, then restart; call if it returns. Steps: fridge section warm, freezer cold
5EFridge defrost sensor errorCall: the sensor needs replacing. Steps: refrigerator running constantly or frosting up
8E, 14EIce maker sensor errorCall. Steps: no ice or water from the dispenser
33EIce pipe heater errorCall. Steps: no ice or water from the dispenser
39E, 39CIce maker errorMake sure the ice bucket is seated; call if it returns. Steps: no ice or water from the dispenser
40E, 40CIce room fan errorCall. Steps: no ice or water from the dispenser
83ECompressor current errorSwitch off the breaker for 60 seconds; call if it returns. Steps: refrigerator not cooling
84CCompressor lockedCall. Steps: refrigerator not cooling
APWi-Fi setup mode, not a faultFinish or cancel the SmartThings setup.

Source: Samsung US: refrigerator error codes; Samsung US: refrigerator shows OF OF, O FF or scrolling bars

LG refrigerator error codes

LG refrigerator error codes
CodeWhat it meansWhat to try first
OF F, OFFDemo mode: the lights work but nothing cools. Not a faultWith a door open, hold Refrigerator and Ice Plus together for 5 seconds. Steps: refrigerator not cooling
FF, Er FFFreezer fan error, often ice blocking the fanUnplug it and leave the doors open at least 8 hours to clear the ice; call if it returns. Steps: fridge section warm, freezer cold
dH, Er dHDefrost faultUnplug it with the doors open for at least 12 hours (towels down), then allow 24–48 hours to cool again; call if it returns. Steps: refrigerator running constantly or frosting up
CF, Er CFCondenser fan errorCall. Steps: refrigerator not cooling
rS, Er rSRefrigerator sensor errorCall. Steps: refrigerator not cooling
FS, Er FSFreezer sensor errorCall. Steps: refrigerator not cooling
IF, Er IFIce maker fan errorCall. Steps: no ice or water from the dispenser
CO, Er COCommunication error between the boardsUnplug it for 60 seconds; call if it returns.

Source: LG USA: refrigerator error code list; LG USA: refrigerator digital and analog error codes

Where's the model number on a refrigerator?

It's on a sticker called the rating label, and you can reach it without tools. The model number tells the tool above (and our technician) which series you have; the serial number on the same label holds the build date. Watch 0 and O, 1 and I, 8 and B.

  • Open the fresh-food door: the refrigerator side, not the freezer.
  • Look here first: Inside, on a side wall near the top. It's most often the left wall, just above the top shelf.
  • Then check: The ceiling of the fresh-food section, or low on a side wall behind the crisper drawers.
  • Read the line marked Model (Mod., M/N or Model No.), not Serial (Ser., S/N). Copy every character, including anything after a dash or slash.
Can't find the label?
  • Check the owner's manual, the receipt, the delivery paperwork or the registration card.
  • If it's connected to the brand's app, the model number is in the app's device information.
  • Can't read it? Take a photo with the flash off, holding the phone at a slight angle so it doesn't glare, then zoom in.
  • Still nothing? Skip it. The guide works without a model number, and our technician will find it at the visit.
How refrigerator model numbers start, by brand
BrandModel number starts with
AmanaART: top-freezer refrigerator · ASI: side-by-side refrigerator · AFI: French-door refrigerator
BoschB36, B30, B24 …: refrigerator
CaféCFE, CYE, CWE, CVE: French-door refrigerator
ElectroluxEI … BS, EW … BS: French-door refrigerator
Fisher & PaykelRF: refrigerator
FrigidaireFFTR, FRTD, FFHT: top-freezer refrigerator · FFSS, FRSS, FFHS, FGSS: side-by-side refrigerator · FRFS, FGHB, FFHB, FG4H: French-door refrigerator · FFBN: bottom-freezer refrigerator
GEGFE, GNE, GYE, GWE, PFE, PYE, PVD: French-door refrigerator · GSS, GSE, GZS, PSE: side-by-side refrigerator · GTE, GTS, GIE: top-freezer refrigerator · GBE, GDE: bottom-freezer refrigerator
HotpointHPS, HPE: top-freezer refrigerator
JennAirJFF: French-door refrigerator
KitchenAidKRF, KRM: French-door refrigerator · KRS: side-by-side refrigerator
LGLF, LM: French-door refrigerator · LR: refrigerator · LSX, LSC: side-by-side refrigerator · LT: top-freezer refrigerator · LB: bottom-freezer refrigerator
LiebherrCS, CBS: refrigerator
MaytagMFI, MFT: French-door refrigerator · MRT: top-freezer refrigerator · MSS: side-by-side refrigerator
SamsungRF: French-door refrigerator · RS, RH: side-by-side refrigerator · RT: top-freezer refrigerator
WhirlpoolWRF, WRX: French-door refrigerator · WRS: side-by-side refrigerator · WRT: top-freezer refrigerator · WRB: bottom-freezer refrigerator

The full guide to finding a model number

Brand notes

  • Samsung. Display shows OF OF, O FF or OFF OFF? That's Samsung's Cooling Off (showroom) mode: cooling, ice and water are switched off and no repair is needed. Turn it off with the button combination for your model. Samsung: Cooling Off mode
  • Samsung. Ice building up around the ice maker in the left door of a French-door model is a known Samsung problem: humid air gets into the ice room and meltwater refreezes. Samsung ice maker frozen over
  • LG. OF F on the display means demo mode: with a door open, hold Refrigerator and Ice Plus together for 5 seconds. Many LG refrigerators also use a linear compressor with its own, longer parts warranty, so check it before paying for a compressor repair. LG linear compressor warranty
  • LG. LG refrigerator not cooling: the usual causes, in the order we find them. LG refrigerator not cooling
  • Viking. Viking built-in refrigerators: the usual causes of a warm section, and why frost builds up. Viking refrigerator not cooling
  • Kenmore. Kenmore appliances are built by other makers, and the three digits before the dot in the model number say which: 110 is Whirlpool laundry, 795 LG refrigerators, 253 Frigidaire refrigerators and freezers. Error codes follow that maker. Kenmore appliance repair

Questions people ask

How long can I wait before calling about a warm refrigerator?

Not long. FoodSafety.gov says food stays safe for about 4 hours in a refrigerator that stays closed. Do the quick checks, move perishables to a cooler with ice, and call if the fresh-food section is still above 40°F after an hour or two. Our refrigeration diagnostic is $85, applied to the repair.

How much does refrigerator repair cost in Los Angeles?

Most refrigerator repairs we do in Los Angeles, Orange and Ventura counties run $160–$1,400 for parts and labor, for example start relay / capacitor $160–$280 and evaporator or condenser fan motor $190–$340. The diagnostic is $85, applied to the repair, and you get a written quote before any work starts.

Is it worth repairing my refrigerator?

Usually, while the repair costs less than half the price of a comparable new refrigerator and it has life left. Most refrigerators last 10–12 years, and premium brands 18–20. Past that age, or when the quote passes half the new price, replacing it is usually the better buy, and we'll tell you so.

Checked everything? Call before noon for a same-day visit.

Dispatch answers the phone and the technician arrives with the likely parts. $85 diagnostic, applied to the repair. Written quote before any work.

Call (866) 696-7767 Book online Mon–Fri 9 am–5 pm · Sat 10 am–2 pm · Emergency calls answered 24/7 · Calls before noon are usually seen the same day

The State of California's record for A49955

California DCA license search record: Household Goods and Services, Bureau of — Licensing details for 49955. Name: Pros Fix Appliances LLC. License type: Major Appliance Repair. License status: CLEAR. Address: 1201 N Pacific Ave #202, Glendale CA 91203, Los Angeles County. Issuance date July 11, 2023. Expiration date July 31, 2027. Current date November 6, 2026.
What the state's license search shows for Pros Fix Appliances LLC, as checked on Nov 6, 2026: status CLEAR, registered since July 11, 2023, valid through July 31, 2027. The live record is one click away — open it on search.dca.ca.gov ↗.