Washer troubleshooting guide
Most washer problems come down to a clogged drain filter, a kinked hose, an unbalanced load or a door that isn't locking. Pick what yours is doing for safe checks in the order our technicians find the cause, what each brand's error code means and when to stop and call.
Last updated
Troubleshoot your washer
Add the brand and model number for brand notes and error codes, then pick what it's doing. Nothing you type leaves this page.
Brand-specific steps and error codes, if we know the series.
Can't find the label?
- Check the owner's manual, the receipt, the delivery paperwork or the registration card.
- If it's connected to the brand's app, the model number is in the app's device information.
- Can't read it? Take a photo with the flash off, holding the phone at a slight angle so it doesn't glare, then zoom in.
- Still nothing? Skip it. The guide works without a model number, and our technician will find it at the visit.
Washer won't drain or spin
A washer that won't drain or spin usually has a clogged drain pump filter, a kinked drain hose, a lid or door that isn't locking, or a load too unbalanced to spin. You can check all four in about 20 minutes.
Most likely, in the order we find it: Drain pump, clogged pump filter, lid or door lock, drive belt or motor control.
-
Run Drain & Spin once
Cancel the cycle, wait a minute, then run Drain & Spin (or Rinse & Spin) on its own.
If it drains and spins now, a glitch or an uneven load was the cause.
-
Even out the load
A single heavy item, like a rug or a comforter, can keep the drum from spinning. Spread the load out or add a couple of towels to balance it.
It spins up smoothly if balance was the problem.
-
Check the drain hose
Pull the washer out a few inches. The drain hose should have no kinks or flat spots and should sit loosely in the standpipe, not jammed deep into it.
Straighten it and run Drain & Spin again.
-
Clean the drain pump filter Front-loaders only
Put towels and a shallow pan down. Open the small door at the bottom front, let the water out through the little drain hose if there is one, then unscrew the filter slowly counterclockwise. Pick out lint, coins and hair ties and screw it back in tight.
Several quarts of water can come out, so go slowly. Most front-loaders drain normally right after this.
You'll need: Towels, a shallow pan, about 20 minutes
-
Listen for the lid lock Top-loaders only
Close the lid firmly and start Drain & Spin. Most newer top-loaders click as the lid locks before they spin, and a flashing Lid Locked light means it can't lock.
No click and no spin points to the lid lock or its switch.
-
Listen to the pump
Start Drain & Spin and listen near the bottom. A hum with no water moving means a blocked or failed pump; silence can be the pump or the control.
Either way, the pump and the lock are tested on the first visit.
Still not working?
- What we check
- Pump operation, filter, lock switch, belt and motor signals
- Typical repair
- Drain pump $190–$340 · Lid lock / door lock assembly $160–$300Parts and labor, typical for LA, OC & Ventura; written quote before any work.
- The visit
- $69 diagnostic, applied to the repair · Usually fixed on the first visit
Read: Washer Won't Spin? Causes, Checks and LA Repair CostsGo through these steps one at a time
Washer leaking
A leaking washer usually has a loose or worn fill hose, a torn door seal, too much detergent, or a drain hose that has slipped out of the standpipe. When the water appears (filling, washing or draining) tells you which.
Most likely, in the order we find it: Door boot/gasket, drain hose, inlet valve, tub seal or pump housing.
-
Keep water away from power
If water has reached the outlet or the cord, switch off the washer's breaker before you touch anything.
-
Watch when it leaks
Run a short cycle with no clothes and watch: during the fill (hoses and inlet valve), the wash (door seal or tub) or the drain (drain hose and pump).
Knowing when narrows it to one or two parts.
-
Tighten the fill hoses
Hand-tighten both hoses at the faucets and at the back of the washer. Replace rubber hoses older than about five years with braided steel ones.
Most leaks during the fill stop here.
-
Check the door seal Front-loaders only
Pull back the rubber door seal and look in the fold for a sock, a tear or hair caught in it. Wipe it clean.
A small tear at the bottom drips during the wash.
-
Use less detergent
Use HE detergent and no more than the line on the cap. Too many suds push water out through the seals and vents.
Leaks that happen only with a full dose are suds.
-
Check the drain hose and standpipe
Make sure the drain hose is secured in the standpipe and the pipe doesn't overflow while the washer drains.
Water around the standpipe means a slow house drain (a plumbing job) or a hose that slipped out.
Still not working?
- What we check
- Where the water appears during fill, wash and drain
- Typical repair
- Door boot (front-load gasket) $220–$420 · Inlet valve $170–$300Parts and labor, typical for LA, OC & Ventura; written quote before any work.
- The visit
- $69 diagnostic, applied to the repair · Usually same-day
Read: Washing Machine Leaking from the Bottom? Causes and CostsGo through these steps one at a time
Washer won't start or has no power
A washer that won't start usually has a tripped breaker, a door or lid that isn't latched, the control lock on or a delay start set. A dark display with power at the outlet points to the control board or an internal fuse.
Most likely, in the order we find it: Door lock, control board, user interface or power supply.
-
Check the power
Make sure it's plugged in and the breaker hasn't tripped. Test the outlet with a lamp or a phone charger.
No power at the outlet is an electrical problem, not the washer.
-
Close the door or lid firmly
Front-load doors need to click shut, and top-load lids must be all the way down. Check for clothes caught in the door.
Most washers won't start with the door or lid open, and many don't say why.
-
Turn off the control lock and delay
A lock icon or CL means the controls are locked: hold the lock button (or the two buttons marked for it) for 3 seconds. Make sure Delay Start isn't set.
The buttons respond again once the lock is off.
-
Reset it
Switch it off at the breaker (or unplug it) for 1 full minute, then switch it back on. Then try Rinse & Spin.
A dark display with power at the outlet means the control board or an internal fuse. Call.
Still not working?
- What we check
- Lock assembly, board voltage, error codes
- Typical repair
- Lid lock / door lock assembly $160–$300 · Main control board $280–$560Parts and labor, typical for LA, OC & Ventura; written quote before any work.
- The visit
- $69 diagnostic, applied to the repair · Usually same-day
Washer shaking or banging
A washer that shakes or bangs is usually unbalanced, not level, or new with its shipping bolts still in. If it still bangs on normal loads after those checks, the shock absorbers or suspension are worn.
Most likely, in the order we find it: Suspension rods or shocks, bearings, or an unbalanced load or uneven feet.
-
Rebalance the load
Pause the cycle and spread the laundry evenly. Wash a single bulky item with a couple of towels.
Most banging during the spin is one heavy, wet item.
-
Level the washer
Push down on opposite corners: it shouldn't rock. Turn the front feet (by hand on most models) until all four sit firmly, then tighten the lock nuts.
A level washer spins much more quietly.
-
Remove the shipping bolts on a new washer Front-loaders only
If the washer is new or was just moved, check the back for transport bolts or spacers. Running it with them in makes it shake violently.
Your manual shows where they are. Keep them for the next move.
-
Check the floor
A springy wood floor magnifies shaking. An anti-vibration pad under the feet helps.
-
Know when to stop
If the drum knocks against the cabinet on normal loads after these checks, stop using the washer.
Worn shock absorbers, suspension rods or a loose counterweight get worse quickly and can damage the tub.
Still not working?
- What we check
- Suspension, bearing play, leveling feet
- Typical repair
- Suspension rods or shocks (set) $220–$380Parts and labor, typical for LA, OC & Ventura; written quote before any work.
- The visit
- $69 diagnostic, applied to the repair · Bearings are scheduled; others same-day
Read: Washer Shaking Violently? Leveling, Bolts and ShocksGo through these steps one at a time
Washer grinding or roaring
Grinding usually means something is caught in the drum or the drain pump. A roar that gets louder as the drum spins faster points to worn drum bearings, which should be checked before the tub is damaged.
Most likely, in the order we find it: Tub bearings, or a coin or bra wire caught in the pump or between the drums.
-
Check the drum and the seal
Empty the drum, turn it by hand and feel for scraping. Check the folds of the door seal, or around the agitator, for coins, keys or bra wires.
Remove anything you find and run a rinse.
-
Clean the drain pump filter Front-loaders only
Coins and buttons in the pump grind while it drains. Clean the filter behind the small door at the bottom front, with towels down.
Grinding that happened only while draining usually stops here.
You'll need: Towels, a shallow pan
-
Note when it roars
Run a spin and listen. A roar that rises with the spin speed, like a jet, is the drum bearings. Grinding only while draining is the pump.
Bearing noise only gets worse. Stop using it and get a repair-or-replace quote.
Still not working?
- What we check
- Pump filter, drum play, bearing noise on spin
- Typical repair
- Drain pump $190–$340 · Tub bearing and seal $450–$750Parts and labor, typical for LA, OC & Ventura; written quote before any work.
- The visit
- $69 diagnostic, applied to the repair · Pump debris same-day; bearings are scheduled
Read: Washing Machine Grinding Noise? Bearings, Coins or PumpGo through these steps one at a time
Washer not filling or filling slowly
A washer that won't fill or fills slowly usually has a faucet that isn't fully open, a kinked hose or clogged inlet screens. If water flows freely to the washer, the inlet valve is the likely repair.
Most likely, in the order we find it: Inlet valve, water pressure, pressure switch or clogged hose screens.
-
Open both faucets fully
Turn both valves behind the washer all the way open.
Half-open valves are common after a move or a plumbing job.
-
Straighten the fill hoses
Pull the washer out and check that neither hose is kinked or crushed against the wall.
-
Rinse the inlet screens
Turn off both faucets, keep a towel ready and unscrew the hoses from the back of the washer. Rinse the small mesh screens inside the washer's inlets in place with an old toothbrush, then reconnect.
Sediment in the screens slows the fill to a trickle.
You'll need: Towel, old toothbrush
-
Check the house water
If other faucets in the house are weak too, the problem is the water supply, not the washer.
-
Check hot and cold
If the washer shows a temperature error, or fills with only hot or only cold, make sure the hot faucet connects to the inlet marked H or red.
Swapped hoses are an easy fix.
Still not working?
- What we check
- Valve coils, screens, pressure-switch hose
- Typical repair
- Inlet valve $170–$300Parts and labor, typical for LA, OC & Ventura; written quote before any work.
- The visit
- $69 diagnostic, applied to the repair · Usually same-day
Read: Washer Won't Fill with Water? Causes, Checks and CostsGo through these steps one at a time
Washer error codes: what to do first
A washer error code names the system that failed: fill, drain, door lock, balance, motor or control. Write it down, fix the obvious cause, reset once and call if it comes back. Each brand's codes are in the tables below.
Most likely, in the order we find it: Depends on the code: lock, drain, motor or communication faults.
-
Write the code down exactly
Note every character, whether it flashes, and when it appeared. A phone photo of the display helps.
Type it into the tool above with your brand, or find it in the tables below.
-
Fix the obvious cause
Drain codes: the drain hose and pump filter. Fill codes: the faucets and hoses. Door codes: close the door firmly. Balance codes: spread the load. Suds codes: less detergent.
-
Reset once
Switch it off at the breaker (or unplug it) for 1 full minute, then switch it back on. Then run Rinse & Spin.
If the code comes straight back, the washer has found a real fault.
-
Call with the code and model number
Send us the code, the model number and when it appears, and the technician brings the likely parts on the first visit.
Still not working?
- What we check
- Read stored codes and test the flagged component
- Typical repair
- Main control board $280–$560Parts and labor, typical for LA, OC & Ventura; written quote before any work.
- The visit
- $69 diagnostic, applied to the repair · Usually same-day
Read: LG Washer Error Codes: OE, IE, UE, dE, LE ExplainedGo through these steps one at a time
Washer error codes by brand
What the code on the display means and what to try first. Codes vary by model and year: if your owner's manual says something different, it wins. If the code comes back after one reset, call with the code and the model number.
Samsung washer error codes
| Code | What it means | What to try first |
|---|---|---|
| 4C, 4E, nF, 1 4C | Not filling: water isn't getting in | Open both faucets fully, straighten the hoses and rinse the inlet screens. Steps: washer not filling or filling slowly |
| 4C2, 4E2, nF1, 14C2 | Hot and cold supply swapped | Connect hot to the hot inlet and cold to cold. Samsung says no service is needed. Steps: washer not filling or filling slowly |
| nd, 5E, SE, 5C, SC, 1 5C | Not draining | Check the drain hose and clean the pump filter on front-loaders. Steps: washer won't drain or spin |
| OE, 0E, OC, 0C, 1 OC | Overflow: too much water in the tub | Turn off both faucets, unplug the washer and call. |
| UE, Ub, Ur, U6, 1 Ub | Unbalanced load | Spread the load, add a towel to a single heavy item and check that the washer is level. Steps: washer shaking or banging |
| dE, dC, dE1, DC1, Ed | Door not closed or not locking | Close the door firmly and check for clothes caught in it. Steps: washer won't start or has no power |
| 9C1, 9C2, 9E1, 9E2, 2E, UC | Power supply problem | Plug it straight into a wall outlet on its own circuit, with no extension cord. Steps: washer won't start or has no power |
| PF | The power went out during the cycle | Restart the cycle. |
| E2, bE2, 6E2 | A button is stuck | Press each button firmly a few times to free it. |
| Sud, SUdS, 5Ud | Too many suds | Let it finish its suds routine, then use HE detergent at the right dose. |
Source: Samsung US: washing machine information and error codes
LG washer error codes
| Code | What it means | What to try first |
|---|---|---|
| OE | Not draining | Clean the drain pump filter (front-loaders: bottom left), straighten the drain hose and run Spin Only. Steps: washer won't drain or spin |
| IE | Not filling in time | Open both valves fully, straighten the hoses and clean the inlet screens. Steps: washer not filling or filling slowly |
| UE, uE | Unbalanced load (lowercase uE: still rebalancing itself) | Spread the load, add an item or two and level the washer. Steps: washer shaking or banging |
| dE, dE1, dE2 | Door or lid not closed or not locking | Push clothes clear of the gasket or lid, close it until it clicks, then reset. Steps: washer won't start or has no power |
| LE, LE1 | Motor locked or overloaded | Power off, remove some laundry, check for a coin or object in the drum, and let it rest 30 minutes. Steps: washer grinding or roaring |
| CE | Motor over-current | Unplug it for 10 seconds and try a cycle; if it persists, shut the water off and call. |
| PE | Water-level sensor can't read the level | Unplug it for 15 seconds and try again; call if it returns. |
| FE | Too much water in the tub | Shut both water valves, run Spin or Drain, unplug it and call. |
| tE | Heating or water-temperature sensor error | Unplug it for 10 seconds and start a new cycle; call if it returns. |
| Sud | Too many suds | Use HE detergent at the recommended dose and run Tub Clean. |
| PF | The power was interrupted | Restart the cycle and check the plug and breaker. |
| CL | Control lock on, not an error | Hold Control Lock (or the two buttons marked for it) for 3 seconds. Steps: washer won't start or has no power |
Source: LG USA: washer error code list · More detail: LG Washer Error Codes: OE, IE, UE, dE, LE Explained
Whirlpool and Maytag washer error codes
Also KitchenAid, JennAir and Amana, which use the same F#E# codes: F is the system, E the fault.
| Code | What it means | What to try first |
|---|---|---|
| F9 E1, F21, F02 | Long drain: not draining in time | Straighten the drain hose, clear the standpipe and clean the pump filter if your model has one. Steps: washer won't drain or spin |
| F8 E1, LF, LO FL | Long fill or low water flow | Open both faucets fully, unkink the hoses and remove any anti-flood device in the line. Steps: washer not filling or filling slowly |
| Sd, Sud, 5d | Too many suds | Let the suds routine finish; use HE detergent at the right dose. |
| uL, OFb | Unbalanced load | Spread the load, level the washer and pair a single heavy item with towels. Steps: washer shaking or banging |
| F5 E2 | Door or lid not locking | Make sure nothing blocks the door or lid and it closes fully. Steps: washer won't start or has no power |
| F7 E1 | Motor speed sensing error | Make sure the shipping bolts are out and the washer isn't overloaded. |
Source: Whirlpool: error codes in front load washers; Whirlpool: LF, top load washer · More detail: Whirlpool Error Codes: Washer, Dryer, Dishwasher, Fridge
Frigidaire and Electrolux washer error codes
| Code | What it means | What to try first |
|---|---|---|
| E11 | Fill took too long | Open both faucets, straighten the hoses and rinse the inlet screens. Steps: washer not filling or filling slowly |
| E13 | Water leak in the tub area | Check the hoses and the door seal; call if it returns. Steps: washer leaking |
| E21 | Water not pumping out fast enough | Clean the drain pump filter or coin trap and check the drain hose. Steps: washer won't drain or spin |
| E35 | Too much water (overfill) | Turn off both faucets and call. |
| E41 | Door open, or the lock not confirmed | Close the door firmly and check for clothes caught in it. Steps: washer won't start or has no power |
| E52 | Motor speed signal lost | Reset once; call if it returns. |
| EF2 | Too much detergent | Use HE detergent at the right dose. |
Source: Sears PartsDirect: Frigidaire front-load washer error codes
Miele washer error codes
| Code | What it means | What to try first |
|---|---|---|
| F10 | Water inlet blocked or restricted | Turn the faucet on fully and take any kinks or loops out of the inlet hose. Steps: washer not filling or filling slowly |
| F11 | Drain restricted | Keep the end of the drain hose no higher than about 3 feet, then clean the drain filter behind the access panel with towels and a tray down. Steps: washer won't drain or spin |
| F15 | Hot water inlet fault | Check that the inlet hose is on the right supply; call if it returns. Steps: washer not filling or filling slowly |
| F16 | Too much foam | Use less detergent (or a low-sudsing one) and run a rinse. |
Source: Miele USA: fault F10 (washer); Miele USA: fault F11 (washer); Miele USA: washer display messages
Where's the model number on a washer?
It's on a sticker called the rating label, and you can reach it without tools. The model number tells the tool above (and our technician) which series you have; the serial number on the same label holds the build date. Watch 0 and O, 1 and I, 8 and B.
Front-load washers
- Open the door.
- Look here first: On the frame around the door opening, usually at the top or on the right side.
- Then check: The back panel, near the top. Look over the top or from the side; there's no need to move the washer.
- Read the line marked Model (Mod., M/N or Model No.), not Serial (Ser., S/N). Copy every character, including anything after a dash or slash.
Top-load washers
- Lift the lid.
- Look here first: Under the lid, or on the top edge at the back of the tub opening.
- Then check: The back of the control panel, or the back or a side of the cabinet.
- Read the line marked Model (Mod., M/N or Model No.), not Serial (Ser., S/N). Copy every character, including anything after a dash or slash.
Can't find the label?
- Check the owner's manual, the receipt, the delivery paperwork or the registration card.
- If it's connected to the brand's app, the model number is in the app's device information.
- Can't read it? Take a photo with the flash off, holding the phone at a slight angle so it doesn't glare, then zoom in.
- Still nothing? Skip it. The guide works without a model number, and our technician will find it at the visit.
| Brand | Model number starts with |
|---|---|
| Amana | NFW: front-load washer · NTW: top-load washer |
| Bosch | WAT, WAW, WGA: compact front-load washer |
| Electrolux | EFLS, ELFW: front-load washer |
| Fisher & Paykel | WH: front-load washer · WL: top-load washer |
| Frigidaire | FFFW, FAFW: front-load washer · FFTW, FTW: top-load washer · FLCE, FLCG: laundry center (top-load washer) |
| GE | GFW, PFW: front-load washer · GTW, PTW: top-load washer · GUD, GUV: laundry center (top-load washer) |
| Hotpoint | HTW: top-load washer |
| LG | WM: front-load washer · WT: top-load washer · WKE, WKG: WashTower (washer and dryer in one unit) |
| Maytag | MHW: front-load washer · MVW: top-load washer |
| Miele | W, WWH, WXI: front-load washer |
| Samsung | WF: front-load washer · WA: top-load washer · WV: FlexWash washer · WD: washer-dryer combo |
| Speed Queen | TC, TR, AWN: top-load washer · FF, AFN, SFN: front-load washer |
| Whirlpool | WFW: front-load washer · WTW: top-load washer |
Brand notes
- LG. LG front-loaders keep the drain pump filter behind the small cover at the bottom left. LG model numbers start with WM for front-loaders and WT for top-loaders. LG washer model numbers
- Whirlpool, Maytag, KitchenAid, JennAir, Amana and Roper. Whirlpool, Maytag, KitchenAid, JennAir and Amana use the same F#E# codes: F is the system and E the fault. Whirlpool error codes explained
- Speed Queen. Speed Queen washers are built for heavy use; when one won't drain, the pump or a clog in it is the usual cause. Speed Queen washer won't drain
- Kenmore. Kenmore appliances are built by other makers, and the three digits before the dot in the model number say which: 110 is Whirlpool laundry, 795 LG refrigerators, 253 Frigidaire refrigerators and freezers. Error codes follow that maker. Kenmore appliance repair
More help with your washer
- Washer repair in Los Angeles, Orange and Ventura counties
- Washer Shaking Violently? Leveling, Bolts and Shocks
- Washer Won't Fill with Water? Causes, Checks and Costs
- Washer Won't Spin? Causes, Checks and LA Repair Costs
- Washing Machine Leaking from the Bottom? Causes and Costs
- Washing Machine Grinding Noise? Bearings, Coins or Pump
- LG Washer Error Codes: OE, IE, UE, dE, LE Explained
Questions people ask
How do I reset my washer?
Switch it off at the breaker or unplug it for 1 full minute, then plug it back in and run Rinse & Spin. That clears most electronic glitches without erasing your settings. If an error code comes straight back, the washer has found a real fault, so note the code and the model number before you call.
How much does washer repair cost in Los Angeles?
Most washer repairs we do in Los Angeles, Orange and Ventura counties run $160–$750 for parts and labor, for example drain pump $190–$340 and lid lock / door lock assembly $160–$300. The diagnostic is $69, applied to the repair, and you get a written quote before any work starts.
Is it worth repairing my washer?
Usually, while the repair costs less than half the price of a comparable new washer and it has life left. Most washers last 10–12 years, and premium brands 15–20. Past that age, or when the quote passes half the new price, replacing it is usually the better buy, and we'll tell you so.
Checked everything? Call before noon for a same-day visit.
Dispatch answers the phone and the technician arrives with the likely parts. $69 diagnostic, applied to the repair. Written quote before any work.